Looks a bit like there's no getty running on the serial port.. Do you get further if you boot into single-user mode?
On 2012/01/31 12:36, Eric Boudrand wrote: > Hi, > > I have tested SOEKRIS4521-50.image on a Soekris NET4511. The boot > sequence failed with this log : > > boot> > > booting hd0a:/bsd: 53407060+463132 [61+127216+116991]=0x339ba3c > > entry point at 0x200120 > > > > [ using 244684 bytes of bsd ELF symbol table ] > > Copyright (c) 1982, 1986, 1989, 1991, 1993 > > The Regents of the University of California. All rights reserved. > > Copyright (c) 1995-2011 OpenBSD. All rights reserved. http://www.OpenBSD.org > > > > OpenBSD 5.0 (SOEKRIS4521) #0: Wed Nov 2 12:07:42 MDT 2011 > > > [email protected]:/obj/SOEKRIS4521 > cpu0: AMD Am486DX4 W/B or Am5x86 W/B 150 ("AuthenticAMD" 486-class) > > cpu0: FPU > > real mem = 66646016 (63MB) > > avail mem = 12173312 (11MB) > > mainbus0 at root > > bios0 at mainbus0: AT/286+ BIOS, date 20/31/19, BIOS32 rev. 0 @ 0xf7840 > > pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000 > > pcibios0: pcibios_get_intr_routing - function not supported > > pcibios0: PCI IRQ Routing information unavailable. > > pcibios0: PCI bus #1 is the last bus > > bios0: ROM list: 0xc8000/0xa000 > > cpu0 at mainbus0: (uniprocessor) > > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > > elansc0 at pci0 dev 0 function 0 "AMD ElanSC520 PCI" rev 0x00: product 0 > steppi> > gpio0 at elansc0: 32 pins > > cbb0 at pci0 dev 9 function 0 "TI PCI1410 CardBus" rev 0x02: irq 10 > > sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq > 11, 8 > nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1 > > sis1 at pci0 dev 19 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 5, > a9 > nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1 > > cardslot0 at cbb0 slot 0 flags 0 > > cardbus0 at cardslot0: bus 1 device 0 cacheline 0x10, lattimer 0x3f > > pcmcia0 at cardslot0 > > isa0 at mainbus0 > > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > > com0: console > > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > > pckbc0 at isa0 port 0x60/5 > > pckbd0 at pckbc0 (kbd slot) > > pckbc0: using irq 1 for kbd slot > > wskbd0 at pckbd0: console keyboard > > wdc0 at isa0 port 0x1f0/8 irq 14 > > wd0 at wdc0 channel 0 drive 0: <SanDisk SDCFH-004G> > > wd0: 1-sector PIO, LBA48, 3815MB, 7813120 sectors > > wd0(wdc0:0:0): using BIOS timings > > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > > Any suggestion is welcome. > > Regards. > > Éric Boudrand > > > _______________________________________________ > flashboot mailing list > [email protected] > https://lists.mindrot.org/mailman/listinfo/flashboot _______________________________________________ flashboot mailing list [email protected] https://lists.mindrot.org/mailman/listinfo/flashboot
