On Sun, Oct 09, 2016 at 12:42:13PM +0200, Moritz Barsnick wrote: > Signed-off-by: Moritz Barsnick <barsn...@gmx.net> > --- > doc/codecs.texi | 2 +- > doc/demuxers.texi | 4 ++-- > doc/ffmpeg.texi | 2 +- > doc/fftools-common-opts.texi | 8 ++++---- > doc/filters.texi | 42 +++++++++++++++++++++--------------------- > doc/formats.texi | 2 +- > doc/indevs.texi | 4 ++-- > doc/muxers.texi | 6 +++--- > doc/platform.texi | 2 +- > doc/protocols.texi | 2 +- > 10 files changed, 37 insertions(+), 37 deletions(-)
[...]
> diff --git a/doc/filters.texi b/doc/filters.texi
> index 4b2f7bf..c3a1559 100644
> --- a/doc/filters.texi
> +++ b/doc/filters.texi
> @@ -911,14 +911,14 @@ A gate is mainly used to reduce lower parts of a
> signal. This kind of signal
> processing reduces disturbing noise between useful signals.
>
> Gating is done by detecting the volume below a chosen level @var{threshold}
> -and divide it by the factor set with @var{ratio}. The bottom of the noise
> +and dividing it by the factor set with @var{ratio}. The bottom of the noise
> floor is set via @var{range}. Because an exact manipulation of the signal
> would cause distortion of the waveform the reduction can be levelled over
> time. This is done by setting @var{attack} and @var{release}.
>
> @var{attack} determines how long the signal has to fall below the threshold
> before any reduction will occur and @var{release} sets the time the signal
> -has to raise above the threshold to reduce the reduction again.
> +has to rise above the threshold to reduce the reduction again.
> Shorter signals than the chosen attack time will be left untouched.
>
> @table @option
> @@ -935,7 +935,7 @@ If a signal rises above this level the gain reduction is
> released.
> Default is 0.125. Allowed range is from 0 to 1.
>
> @item ratio
> -Set a ratio about which the signal is reduced.
> +Set a ratio by which the signal is reduced.
> Default is 2. Allowed range is from 1 to 9000.
>
> @item attack
> @@ -958,19 +958,19 @@ Default is 2.828427125. Allowed range is from 1 to 8.
>
> @item detection
> Choose if exact signal should be taken for detection or an RMS like one.
> -Default is rms. Can be peak or rms.
> +Default is @code{rms}. Can be @code{peak} or @code{rms}.
>
> @item link
> Choose if the average level between all channels or the louder channel
> affects
> the reduction.
> -Default is average. Can be average or maximum.
> +Default is @code{average}. Can be @{average} or @{maximum}.
*** '}' without opening '{' before: or @{maximum}. (in doc/filters.texi l. 966)
*** '}' without opening '{' before: . (in doc/filters.texi l. 966)
[...]
--
Michael GnuPG fingerprint: 9FF2128B147EF6730BADF133611EC787040B0FAB
I have often repented speaking, but never of holding my tongue.
-- Xenocrates
signature.asc
Description: Digital signature
_______________________________________________ ffmpeg-devel mailing list ffmpeg-devel@ffmpeg.org http://ffmpeg.org/mailman/listinfo/ffmpeg-devel
