On Sunday 30 October 2016 19:11:53 W. Martinjak wrote: > Hi Gene, > > back again. > > On 2016-10-30 22:17, Gene Heskett wrote: > >> > Stay tuned! > > > > I am but that station seems be be off the air? Does it need a good > > broadcast engineer with a 1st phone in his pocket? ;-) > > Yes, something likethat. ;) > > Back to the raspi install. > > I will send you a link to an archive with files for installing the > necessary packages per personal mail. > > Its easier. > Got it, but its on this machine, not the pi, and I am not convinced there is an easier way than setting up the sshfs share to /home/gene/linuxcnc/r_pi_nc_files. But first, since all my sshfs shares are owned by gene, user 1000 on all machines here, is it sufficient that I add me to the pi group on the pi? But that didn't seem to help, so I'll do an adduser gene and add me to the sudoers file.
That worked, I have this machine now mounted at the r-pi's /sshnet/coyote, and installed mc to copy the packed file with. > Archive content: > > pkglistfile.txt > install-script.sh > > and the linuxcnc arm packages. > > Put all in a install directory of your preferred name. > > cd to this dir. > humm, unpacked it, then exec'd the line below with no apparent lag or results. But when I looked after the 2nd try, I had a new subdir "debian-arm" and it contained this: install-script.sh linuxcnc-doc-es_2.8.0~pre1_all.deb linuxcnc-uspace_2.8.0~pre1_armhf.deb pkglistfile.txt linuxcnc-doc-en_2.8.0~pre1_all.deb linuxcnc-doc-fr_2.8.0~pre1_all.deb linuxcnc-uspace-dev_2.8.0~pre1_armhf.deb So I assume, after cd-ing to debian-arm, I should repeat the script execution below. > Then type > > sudo install-script.sh pkglistfile.txt >aptget.log 2>apterr.log > which needed ./ in front of the files, and is busy, but silently writing to the u-sd. And still is about 5 minutes later. While hammering on my net connection. :) Now, at 10 minutes, the net traffic has nearly finished, but the green led is on about 99% of the time, with no pattern to the off blinks. Chips and u-sd are warm but not alarmingly so. At 25 minutes its still puttering along. Net traffic fires up again from time to time. Its not done, but I just got an X error: X11 connection rejected because of wrong authentication. I assume because its gene and not pi at the wheel? I probably need to add myself to a few group's. And now I have 2 of those errors. But 80 minutes on its still going. Took 86 minutes. > @ 1st ignore the errors and warnings. > > Then > > dpkg -i linuxcnc-* gene@raspberrypi:~/linuxcnc/debian-arm $ sudo dpkg -i linuxcnc-* Selecting previously unselected package linuxcnc-doc-en. (Reading database ... 125206 files and directories currently installed.) Preparing to unpack linuxcnc-doc-en_2.8.0~pre1_all.deb ... Unpacking linuxcnc-doc-en (1:2.8.0~pre1) ... Selecting previously unselected package linuxcnc-doc-es. Preparing to unpack linuxcnc-doc-es_2.8.0~pre1_all.deb ... Unpacking linuxcnc-doc-es (1:2.8.0~pre1) ... Selecting previously unselected package linuxcnc-doc-fr. Preparing to unpack linuxcnc-doc-fr_2.8.0~pre1_all.deb ... Unpacking linuxcnc-doc-fr (1:2.8.0~pre1) ... Selecting previously unselected package linuxcnc-uspace. Preparing to unpack linuxcnc-uspace_2.8.0~pre1_armhf.deb ... Unpacking linuxcnc-uspace (1:2.8.0~pre1) ... Selecting previously unselected package linuxcnc-uspace-dev. Preparing to unpack linuxcnc-uspace-dev_2.8.0~pre1_armhf.deb ... Unpacking linuxcnc-uspace-dev (1:2.8.0~pre1) ... Setting up linuxcnc-doc-en (1:2.8.0~pre1) ... Setting up linuxcnc-doc-es (1:2.8.0~pre1) ... Setting up linuxcnc-doc-fr (1:2.8.0~pre1) ... Setting up linuxcnc-uspace (1:2.8.0~pre1) ... Processing triggers for shared-mime-info (1.3-1) ... Setting up linuxcnc-uspace-dev (1:2.8.0~pre1) ... Processing triggers for mime-support (3.58) ... Processing triggers for man-db (2.7.0.2-5) ... Processing triggers for systemd (215-17+deb8u5) ... Processing triggers for libc-bin (2.19-18+deb8u6) ... >From apterr.log: E: Unable to locate package linux-firmware-image-rpi-rt E: Unable to locate package linux-headers-rpi2-rt E: Unable to locate package linux-image-rpi2-rt And from aptget.log: Begin freedesktop install... Install icon: 32x32 xdg-icon-resource: No writable system icon directory found. xdg-icon-resource: No writable system icon directory found. Install icon: 48x48 xdg-icon-resource: No writable system icon directory found. xdg-icon-resource: No writable system icon directory found. Install icon: 64x64 xdg-icon-resource: No writable system icon directory found. xdg-icon-resource: No writable system icon directory found. Install icon: 128x128 xdg-icon-resource: No writable system icon directory found. xdg-icon-resource: No writable system icon directory found. Install icon: 256x256 xdg-icon-resource: No writable system icon directory found. xdg-icon-resource: No writable system icon directory found. Install mime type Install menu items xdg-desktop-menu: No writable system menu directory found. Done! Apache2 did a lot of fussing about no such file or directory. So lets see if it will run the uspace version, yup, and lathe_pawn.ngc runs. Slow though. Very slow, pgm says F50 ipm, sim is moving less than 2 ipm.0 But I'd imagine that is fixable, the point is, its running. Thank you very much. > > Now check the errors if there are fatals. :) See above. I copy/pasted them from the login terminal. > > And then tell me please how did it go. > > I wish you fun again, > I believe making it run 1500 lbs of an 11x36 Sheldon _is_ going to be fun. And I expect some of my questions may be dumb. This is 100% new dirt I am walking on with this. Thanks again. > Matsche Cheers, Gene Heskett -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) Genes Web page <http://geneslinuxbox.net:6309/gene> ------------------------------------------------------------------------------ The Command Line: Reinvented for Modern Developers Did the resurgence of CLI tooling catch you by surprise? Reconnect with the command line and become more productive. Learn the new .NET and ASP.NET CLI. Get your free copy! http://sdm.link/telerik _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
