hi folks, i have been testing emc2 for motion control from a time now, and came to some questions about motion blending in my setup, that i like to contribute to solve (and dont have enough knowledge! for that im asking)
The setup is a fairly simple aplication for a filament winding machine, similar to a lathe, but with naming convention as this: x linear carriage parallel to mandrel rotation about mandrel axis is A transversal axis is Y. I think this is trivial, and use trivkins. Running some files(copy a portion below) with y axis fixed at some position, Axis Gui plot something similar to a thread back and forth, the plot is ok (change repeat to 1 to see 1 cycle) i have use inverse time feed rate (to some fixed filament speed), machine is metric, A is angular in degrees with 2000°/sec speed and 5000°/sec´2 accel. X have 400mm/sec and 3000mm/sec´2. EMC2 version is 2.4.6 The problem is with motion blending, A axis comes to a dead stop between segments, and i dont know how to make a movement similar to CV . The machine is shaking hardly due to high accel and deceleration between segments in A axis. I have try to write small segments like A1.8, interpolation and blending are fine but speed goes down (i think is the interpreter speed is limiting this). Any clues? Regads and many thanks for reading! Rick PS: GCODE g91 g91.1 g94 g64 g90 G0Y0.00 X17.41B0C0 Y50 m00 o100 repeat [24] g91 g93 G1A 11.98 X 1.87 Y 0 B 0 C 0 F 902.26 A 11.66 X 2.13 Y 0 B 0 C 0 F 925.93 A 11.29 X 2.28 Y 0 B 0 C 0 F 956.94 A 11.38 X 2.50 Y 0 B 0 C 0 F 949.37 A 12.08 X 2.53 Y 0 B 0 C 0 F 894.19 A 10.11 X 2.54 Y 0 B 0 C 0 F 1067.62 A 11.27 X 3.47 Y 0 B 0 C 0 F 958.47 A 10.98 X 3.73 Y 0 B 0 C 0 F 983.61 A 12.32 X 4.60 Y 0 B 0 C 0 F 875.91 A 10.89 X 4.46 Y 0 B 0 C 0 F 991.74 A 11.66 X 5.22 Y 0 B 0 C 0 F 925.93 A 10.49 X 5.15 Y 0 B 0 C 0 F 1029.16 A 11.05 X 5.93 Y 0 B 0 C 0 F 977.20 A 10.06 X 5.92 Y 0 B 0 C 0 F 1073.35 A 10.51 X 6.75 Y 0 B 0 C 0 F 1027.40 A 11.38 X 6.11 Y 0 B 0 C 0 F 949.37 A 10.21 X 4.58 Y 0 B 0 C 0 F 1058.20 A 1002.41 X 421.87 Y 0 B 0 C 0 F 10.77 A 11.79 X 4.60 Y 0 B 0 C 0 F 916.03 A 10.16 X 3.58 Y 0 B 0 C 0 F 1061.95 A 10.18 X 3.58 Y 0 B 0 C 0 F 1060.07 A 11.61 X 4.48 Y 0 B 0 C 0 F 930.23 A 11.01 X 5.06 Y 0 B 0 C 0 F 980.39 A 12.19 X 1.87 Y 0 B 0 C 0 F 886.26 A 10.86 X 1.16 Y 0 B 0 C 0 F 995.02 A 12.08 X 1.13 Y 0 B 0 C 0 F 894.19 A 13.61 X 1.03 Y 0 B 0 C 0 F 793.65 A 19.05 X 1.03 Y 0 B 0 C 0 F 567.11 A 56.34 X -1.23 Y 0 B 0 C 0 F 191.69 A 15.33 X -1.22 Y 0 B 0 C 0 F 704.23 A 13.84 X -1.14 Y 0 B 0 C 0 F 780.23 A 12.68 X -1.42 Y 0 B 0 C 0 F 851.06 A 12.03 X -1.51 Y 0 B 0 C 0 F 896.86 A 12.02 X -1.74 Y 0 B 0 C 0 F 898.20 A 11.91 X -2.07 Y 0 B 0 C 0 F 907.72 A 11.53 X -2.15 Y 0 B 0 C 0 F 936.04 A 11.21 X -2.37 Y 0 B 0 C 0 F 963.08 A 23.45 X -5.05 Y 0 B 0 C 0 F 460.48 A 12.10 X -3.41 Y 0 B 0 C 0 F 892.86 A 11.12 X -3.61 Y 0 B 0 C 0 F 970.87 A 10.58 X -3.75 Y 0 B 0 C 0 F 1020.41 A 11.68 X -4.53 Y 0 B 0 C 0 F 924.50 A 10.42 X -4.42 Y 0 B 0 C 0 F 1036.27 A 11.22 X -5.19 Y 0 B 0 C 0 F 963.08 A 10.15 X -5.13 Y 0 B 0 C 0 F 1063.83 A 10.76 X -5.93 Y 0 B 0 C 0 F 1003.34 A 11.13 X -6.76 Y 0 B 0 C 0 F 970.87 A 10.84 X -6.80 Y 0 B 0 C 0 F 996.68 A 10.81 X -5.33 Y 0 B 0 C 0 F 1000.00 A 10.86 X -4.66 Y 0 B 0 C 0 F 995.02 A 991.27 X -417.19 Y 0 B 0 C 0 F 10.90 A 11.21 X -4.68 Y 0 B 0 C 0 F 963.08 A 12.34 X -4.53 Y 0 B 0 C 0 F 875.91 A 10.18 X -3.58 Y 0 B 0 C 0 F 1060.07 A 10.12 X -3.58 Y 0 B 0 C 0 F 1067.62 A 10.07 X -4.48 Y 0 B 0 C 0 F 1073.35 A 10.14 X -3.86 Y 0 B 0 C 0 F 1065.72 A 13.08 X -1.68 Y 0 B 0 C 0 F 826.45 A 11.24 X -1.15 Y 0 B 0 C 0 F 961.54 A 12.55 X -1.10 Y 0 B 0 C 0 F 860.83 A 19.03 X -1.26 Y 0 B 0 C 0 F 567.64 A 69.16 X 1.10 Y 0 B 0 C 0 F 156.17 A 16.30 X 1.25 Y 0 B 0 C 0 F 662.98 A 13.71 X 1.24 Y 0 B 0 C 0 F 787.40 A 11.25 X 1.34 Y 0 B 0 C 0 F 960.00 A 17.09 X 2.39 Y 0 B 0 C 0 F 632.24 o100 endrepeat m30 ------------------------------------------------------------------------------ Live Security Virtual Conference Exclusive live event will cover all the ways today's security and threat landscape has changed and how IT managers can respond. Discussions will include endpoint security, mobile security and the latest in malware threats. http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/ _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
