Hi Donnie, I just updated the rtai modules package, you'll get an update soon (if your box is connected to the internet). Basicly it'll do the same thing as you manually did.
Regards, Alex On Sun, 2009-01-04 at 14:38 -0500, Donnie Timmons wrote: > Alex > > That seams to have corrected the problem. Rebooted a couple of times and > EMC2 starts the first time now. > > Would have a lead on some documentation that would help a newbie set up the > I/O for a 5i23 with the 7i33 and 7i37 cards? > > Donne > ----- Original Message ----- > From: "Alex Joni" <[email protected]> > To: "Enhanced Machine Controller (EMC)" <[email protected]> > Sent: Sunday, January 04, 2009 2:52 PM > Subject: Re: [Emc-users] EMC startup error > > > > Try removing this symlink: > > > > from http://www.linuxcnc.org/irc/irc.freenode.net:6667/emc/2008-09-11.txt > > 21:27:57 <alex_joni> robh: a temp fix is to remove a symlink : 'sudo rm > > /lib/modules/2.6.24-16-rtai/rtai' > > > > If it makes it work for you, let us know and we'll push a fixed package. > > > > Regards, > > Alex > > > > ----- Original Message ----- > > From: "Donnie Timmons" <[email protected]> > > To: "Enhanced Machine Controller (EMC)" <[email protected]> > > Sent: Sunday, January 04, 2009 8:08 PM > > Subject: Re: [Emc-users] EMC startup error > > > > > > > Alex > > > > > > This the results You may have something. Question how would we fix it? > > > > > > > > > don...@mill:~$ lsmod > > > Module Size Used by > > > ipv6 221780 8 > > > i915 28416 2 > > > drm 73620 3 i915 > > > rfcomm 34580 2 > > > l2cap 21124 13 rfcomm > > > bluetooth 50920 4 rfcomm,l2cap > > > ppdev 8580 0 > > > iptable_filter 2816 0 > > > ip_tables 12232 1 iptable_filter > > > x_tables 13700 1 ip_tables > > > lp 10636 0 > > > parport 33224 2 ppdev,lp > > > snd_intel8x0 29596 3 > > > snd_ac97_codec 90160 1 snd_intel8x0 > > > ac97_bus 1920 1 snd_ac97_codec > > > snd_pcm_oss 37920 0 > > > snd_mixer_oss 15744 1 snd_pcm_oss > > > snd_pcm 65416 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss > > > snd_seq_dummy 3844 0 > > > snd_seq_oss 30740 0 > > > snd_seq_midi 8096 0 > > > hm2_pci 9116 0 > > > hostmot2 55936 1 hm2_pci > > > hal_lib 33304 2 hm2_pci,hostmot2 > > > snd_rawmidi 22560 1 snd_seq_midi > > > rtapi 33540 3 hm2_pci,hostmot2,hal_lib > > > snd_seq_midi_event 6912 2 snd_seq_oss,snd_seq_midi > > > rtai_fifos 25760 1 rtapi > > > rtai_sem 22016 1 rtapi > > > snd_seq 44956 6 > > > snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event > > > snd_timer 21252 2 snd_pcm,snd_seq > > > snd_seq_device 8076 5 > > > snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq > > > psmouse 35728 0 > > > rtai_sched 102160 3 rtapi,rtai_fifos,rtai_sem > > > snd 48564 17 > > > > snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_dummy, > snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device > > > serio_raw 6660 0 > > > rtai_hal 38180 4 rtapi,rtai_fifos,rtai_sem,rtai_sched > > > dcdbas 7584 0 > > > soundcore 7108 1 snd > > > evdev 10752 1 > > > pcspkr 3072 0 > > > snd_page_alloc 9992 2 snd_intel8x0,snd_pcm > > > i2c_i810 4484 0 > > > iTCO_wdt 11296 0 > > > iTCO_vendor_support 3716 1 iTCO_wdt > > > i2c_algo_bit 5892 1 i2c_i810 > > > intel_agp 22804 1 > > > agpgart 31024 3 drm,intel_agp > > > i2c_core 22032 2 i2c_i810,i2c_algo_bit > > > ext3 118920 1 > > > jbd 38036 1 ext3 > > > mbcache 7808 1 ext3 > > > sg 33312 0 > > > sr_mod 15396 0 > > > cdrom 32796 1 sr_mod > > > sd_mod 26640 3 > > > ata_piix 15748 2 > > > ata_generic 7044 0 > > > e1000 110016 0 > > > libata 134452 2 ata_piix,ata_generic > > > scsi_mod 139988 4 sg,sr_mod,sd_mod,libata > > > ehci_hcd 28300 0 > > > uhci_hcd 21392 0 > > > usbcore 119348 3 ehci_hcd,uhci_hcd > > > fuse 43284 3 > > > don...@mill:~$ > > > > > > ----- Original Message ----- > > > From: "Alex Joni" <[email protected]> > > > To: "Enhanced Machine Controller (EMC)" > <[email protected]> > > > Sent: Sunday, January 04, 2009 5:40 AM > > > Subject: Re: [Emc-users] EMC startup error > > > > > > > > >> I think this is related to the hotplug mechanism. > > >> When your PC boots it detects the mesa board, and hotplugs it (loads > the > > >> driver for it). > > >> Can you reboot your PC, and after the fresh boot send us the output > from > > >> lsmod ? > > >> > > >> Regards, > > >> Alex > > >> > > >> ----- Original Message ----- > > >> From: "Donnie Timmons" <[email protected]> > > >> To: "Enhanced Machine Controller (EMC)" > <[email protected]> > > >> Sent: Sunday, January 04, 2009 6:49 AM > > >> Subject: Re: [Emc-users] EMC startup error > > >> > > >> > > >> > :-) > > >> > > > >> > I found the problem with the encoder. It helps to be switching the > wire > > >> > to > > >> > the right encoder. I over look the fact that axis 0 and 2 are on TB1 > > >> > and 1 > > >> > and 3 are on TB2. > > >> > > > >> > Still having the startup problem after a power down in that I have to > > >> > start > > >> > EMC two times with the first erroring out. After that it will start > > >> > ever > > >> > time till power down again. > > >> > > > >> > Donnie > > >> > ----- Original Message ----- > > >> > From: "Peter C. Wallace" <[email protected]> > > >> > To: "Enhanced Machine Controller (EMC)" > > >> > <[email protected]> > > >> > Sent: Saturday, January 03, 2009 11:51 PM > > >> > Subject: Re: [Emc-users] EMC startup error > > >> > > > >> > > > >> >> On Sat, 3 Jan 2009, Donnie Timmons wrote: > > >> >> > > >> >> > Date: Sat, 3 Jan 2009 22:25:38 -0500 > > >> >> > From: Donnie Timmons <[email protected]> > > >> >> > Reply-To: "Enhanced Machine Controller (EMC)" > > >> >> > <[email protected]> > > >> >> > To: "Enhanced Machine Controller (EMC)" > > >> > <[email protected]> > > >> >> > Subject: Re: [Emc-users] EMC startup error > > >> >> > > > >> >> > Peter > > >> >> > > > >> >> > I have TTL encoders so the /A and /B are not used or do I have > > >> >> > connect > > >> > them > > >> >> > to ground? Is there any setting other than the jumps on the 7i33 > to > > >> >> > set > > >> > for > > >> >> > TTL > > >> >> > > >> >> > > >> >> Oh ok, for TTL leave the /A and /B inputs unconnected. I would check > > >> >> the > > >> >> signal levels with a 'scope or DVM though... > > >> >> > > >> >> Peter Wallace > > >> >> > > >> > >> ------------------------------------------------------------------------- > - > > >> > ---- > > >> >> _______________________________________________ > > >> >> Emc-users mailing list > > >> >> [email protected] > > >> >> https://lists.sourceforge.net/lists/listinfo/emc-users > > >> > > > >> > > > >> > > -------------------------------------------------------------------------- > ---- > > >> > _______________________________________________ > > >> > Emc-users mailing list > > >> > [email protected] > > >> > https://lists.sourceforge.net/lists/listinfo/emc-users > > >> > > >> > > > >> ------------------------------------------------------------------------- > ------- > > >> > > >> > > >> > > >> No virus found in this incoming message. > > >> Checked by AVG - http://www.avg.com > > >> Version: 8.0.176 / Virus Database: 270.10.2/1873 - Release Date: > > >> 03.01.2009 > > >> 14:14 > > >> > > >> > > > >> ------------------------------------------------------------------------- > ----- > > >> _______________________________________________ > > >> Emc-users mailing list > > >> [email protected] > > >> https://lists.sourceforge.net/lists/listinfo/emc-users > > > > -------------------------------------------------------------------------- > ---- > > > _______________________________________________ > > > Emc-users mailing list > > > [email protected] > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > > > > > No virus found in this incoming message. > > Checked by AVG - http://www.avg.com > > Version: 8.0.176 / Virus Database: 270.10.2/1873 - Release Date: > 03.01.2009 > > 14:14 > > > > > > -------------------------------------------------------------------------- > ---- > > _______________________________________________ > > Emc-users mailing list > > [email protected] > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > ------------------------------------------------------------------------------ > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
