thanks Bill my original post 2 months ago have a cc to k3support but no answer from Elecraft
i sent them again an email 73, Jorge El jue, 6 jun 2024 a las 16:48, Bill Johnson (<[email protected]>) escribió: > Jorge, email elecraft support to get good guidance. > > Bill > K9YEQ > > Bill > K9YEQ > ------------------------------ > *From:* [email protected] <[email protected]> > on behalf of Jorge Diez - CX6VM <[email protected]> > *Sent:* Thursday, June 6, 2024 12:41:26 PM > *To:* Robert Bajuk <[email protected]> > *Cc:* [email protected] <[email protected]> > *Subject:* Re: [Elecraft] K3 no transmitting > > hello to all > > finally a local friend, couldn´t fix the TX problem with my K3 > > He follow all instructions that Robert gave me to check the LPA, but all > was OK, but the K3 go to TX but no RF output > > He is sending the K3 to my house again. > > Don´t know what else to test?, but it seems I will need to send it to the > USA with someone that travels there. > > Do you know where to send it for service? I think Elecraft will not support > anymore the K3 > > 73, > Jorge > CX6VM/CW5W > > El jue, 9 may 2024 a las 10:35, Robert Bajuk (<[email protected]>) > escribió: > > > Hi Jorge, > > > > Try this source > > > > https://groups.io/g/Elecraft-K3/topic/replacing_k3_lpa_devices/18108669 > > > > 73 Robert, S57AW > > > > On Thu, 9 May 2024, 15:08 Jorge Diez - CX6VM, <[email protected]> > > wrote: > > > >> hello! > >> > >> I have a friend that is trying to get to LPA on the K3 > >> > >> Really it needs to disassemble practically all the K3 or there's a way > to > >> get to this LPA plaque easily? > >> > >> I will appreciate if you can point me to some video about how to > >> disassemble the K3 to get to LPA > >> > >> thanks!! > >> > >> 73, > >> Jorge > >> CX6VM/CW5W > >> > >> El vie, 8 mar 2024 a las 17:26, Robert Bajuk (<[email protected]>) > >> escribió: > >> > >>> Hi Jorge, > >>> > >>> Check D1 first and parts around on 10W LPA boars as already suggested > >>> > >>> See the pics attached, LPA board and D1 marked with red, hope pics pass > >>> over the reflector > >>> > >>> 73 Robert, S57AW > >>> > >>> > >>> > >>> On Fri, Mar 8, 2024 at 8:31 PM Jorge Diez - CX6VM < > [email protected]> > >>> wrote: > >>> > >>>> thanks Steve > >>>> > >>>> Could you please point me to the assembly manual page to find it? > >>>> > >>>> Mine is factory assembled, but I need to fix it here in my country, I > >>>> need > >>>> to try > >>>> > >>>> Thanks very much! > >>>> > >>>> 73, > >>>> Jorge > >>>> CX6VM/CW5W > >>>> > >>>> El vie, 8 mar 2024 a las 13:32, Steve Cooke (<[email protected]>) > >>>> escribió: > >>>> > >>>> > Jorge ..... my K3 displayed the same fault sometime ago .Turned out > to > >>>> > be D1 on the LPA ....a very fine hairline crack in the solder joint > >>>> > ...without Keith Trinity W6ER's advice in a previous reply to > somebody > >>>> > else , I would never have found it . > >>>> > > >>>> > It was only visible under a bright light ...and a > >>>> > magnifying glass . > >>>> > > >>>> > 73 steve G1MPW. > >>>> > > >>>> > > >>>> > On 08/03/2024 13:58, Jorge Diez - CX6VM wrote: > >>>> > > hello > >>>> > > > >>>> > > My newer K3 is not TX anymore, on any mode, CW, SSB, FT8 > >>>> > > > >>>> > > > >>>> > ______________________________________________________________ > >>>> > Elecraft mailing list > >>>> > Home: http://mailman.qth.net/mailman/listinfo/elecraft > >>>> > Help: http://mailman.qth.net/mmfaq.htm > >>>> > Post: mailto:[email protected] <[email protected]> > >>>> > > >>>> > This list hosted by: http://www.qsl.net > >>>> > Please help support this email list: http://www.qsl.net/donate.html > >>>> > Message delivered to [email protected] > >>>> > >>>> > >>>> > >>>> -- > >>>> 73, > >>>> Jorge > >>>> CX6VM/CW5W > >>>> ______________________________________________________________ > >>>> Elecraft mailing list > >>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >>>> Help: http://mailman.qth.net/mmfaq.htm > >>>> Post: mailto:[email protected] <[email protected]> > >>>> > >>>> This list hosted by: http://www.qsl.net > >>>> Please help support this email list: http://www.qsl.net/donate.html > >>>> Message delivered to [email protected] > >>> > >>> > >> > >> -- > >> 73, > >> Jorge > >> CX6VM/CW5W > >> > > > > -- > 73, > Jorge > CX6VM/CW5W > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] <[email protected]> > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] > -- 73, Jorge CX6VM/CW5W ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
