[PATCH 04/21] staging: wilc1000: remove warnings on the multiple line uses

[Tony Cho]

This patch removes the warnings reported by checkpatch.pl for using
multiple blank lines.

Signed-off-by: Tony Cho <tony....@atmel.com>
---
 drivers/staging/wilc1000/wilc_sdio.c | 14 --------------
 1 file changed, 14 deletions(-)

diff --git a/drivers/staging/wilc1000/wilc_sdio.c 
b/drivers/staging/wilc1000/wilc_sdio.c
index 897e47e..632b2b0 100644
--- a/drivers/staging/wilc1000/wilc_sdio.c
+++ b/drivers/staging/wilc1000/wilc_sdio.c
@@ -10,7 +10,6 @@
 #include "wilc_wlan_if.h"
 #include "wilc_wlan.h"
 
-
 #ifdef WILC1000_SINGLE_TRANSFER
 #define WILC_SDIO_BLOCK_SIZE 256
 #else
@@ -90,7 +89,6 @@ static int sdio_set_func0_csa_address_byte0(uint32_t adr)
 {
        sdio_cmd52_t cmd;
 
-
        /**
         *      Review: BIG ENDIAN
         **/
@@ -222,8 +220,6 @@ uint32_t sdio_xfer_cnt(void)
        cnt |= (cmd.data << 16);
 
        return cnt;
-
-
 }
 
 /********************************************
@@ -412,7 +408,6 @@ static int sdio_write(uint32_t addr, uint8_t *buf, uint32_t 
size)
 
                }
 
-
                if (rest > 0) {
                        cmd.block_mode = 1;
                        cmd.increment = 1;
@@ -458,7 +453,6 @@ static int sdio_write(uint32_t addr, uint8_t *buf, uint32_t 
size)
 #endif /* platform */
        }
 
-
        if (nleft > 0) {
                cmd.block_mode = 0;
                cmd.increment = 1;
@@ -622,7 +616,6 @@ static int sdio_read(uint32_t addr, uint8_t *buf, uint32_t 
size)
                        cmd.buffer = buf;
                        cmd.block_size = block_size;
 
-
                        if (addr > 0) {
                                if (!sdio_set_func0_csa_address(addr))
                                        goto _fail_;
@@ -639,7 +632,6 @@ static int sdio_read(uint32_t addr, uint8_t *buf, uint32_t 
size)
 
                }
 
-
                if (rest > 0) {
                        cmd.block_mode = 1;
                        cmd.increment = 1;
@@ -898,7 +890,6 @@ static int sdio_init(wilc_wlan_inp_t *inp, wilc_debug_func 
func)
        }
        g_sdio.dPrint(N_ERR, "[wilc sdio]: has_thrpt_enh3 = %d...\n", 
g_sdio.has_thrpt_enh3);
 
-
        return 1;
 
 _fail_:
@@ -1097,7 +1088,6 @@ static int sdio_clear_int_ext(uint32_t val)
                }
 #endif /* WILC_SDIO_IRQ_GPIO */
 
-
                {
                        uint32_t vmm_ctl;
 
@@ -1138,7 +1128,6 @@ static int sdio_sync_ext(int nint /*  how mant interrupts 
to enable. */)
 {
        uint32_t reg;
 
-
        if (nint > MAX_NUM_INT) {
                g_sdio.dPrint(N_ERR, "[wilc sdio]: Too many interupts 
(%d)...\n", nint);
                return 0;
@@ -1148,7 +1137,6 @@ static int sdio_sync_ext(int nint /*  how mant interrupts 
to enable. */)
                return 0;
        }
 
-
        g_sdio.nint = nint;
 
        /**
@@ -1170,7 +1158,6 @@ static int sdio_sync_ext(int nint /*  how mant interrupts 
to enable. */)
                uint32_t reg;
                int ret, i;
 
-
                /**
                 *      interrupt pin mux select
                 **/
@@ -1225,7 +1212,6 @@ static int sdio_sync_ext(int nint /*  how mant interrupts 
to enable. */)
        return 1;
 }
 
-
 /********************************************
  *
  *      Global sdio HIF function table
-- 
1.9.1

_______________________________________________
devel mailing list
de...@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel