Amit Barzilai <[email protected]> writes:
> The Solomon SSD1351 is a 128x128 RGB color OLED controller. It shares the
> SSD133X pixel layout: one 65k color (RGB565) pixel per Segment, written as
> a bulk transfer once a column/row addressing window has been programmed.
> Add it as a new SSD135X_FAMILY rather than as a separate driver, so that
> the ssd130x plane, CRTC and encoder infrastructure is reused.
>
> Give the family its own primary plane update and disable, encoder enable
> and backlight callbacks instead of teaching the ssd133x ones about a second
> family. Only the callbacks that carry no family specific logic are reused
> as is: ssd133x_primary_plane_atomic_check(), ssd133x_crtc_atomic_check()
> and ssd130x_encoder_atomic_disable().
>
> The data path differs from the ssd133x family in one respect. The SSD1351
> only starts accepting pixel data after an explicit Write RAM command
> (0x5c), while the SSD133X enters data mode as soon as the address window
> has been programmed. Emit it from ssd135x_update_rect(), which both the
> damage update and the clear screen paths go through.
>
> SSD1351 differs from previous controllers in the command protocol. While
> the opcode is still sent on the command path, the parameters are sent on
> the data path. Introduce the cmd_params_are_data flag to struct
> ssd130x_deviceinfo and let ssd130x_write_cmds() split the buffer in
> accordance to the device specifications.
>
> The SSD1351 also needs its own init sequence (ssd135x_init). The remap
> byte is fixed at horizontal address increment, COM split, reversed COM
> scan direction, BGR sub-pixel order and 65k color depth; rotation is not
> supported.
>
> Contrast is calibrated per color channel as for the ssd133x family, but
> the three channels are parameters of a single command (0xc1) instead of
> one command per channel. Add ssd135x_set_contrast() for that and use it
> from both the init and the backlight update paths.
>
> The SSD1351 is SPI-only, so only the SPI transport match tables gain an
> entry; no new config symbol is needed.
>
> Assisted-by: Claude:claude-opus-5
> Signed-off-by: Amit Barzilai <[email protected]>
> ---
[...]
> static int ssd130x_write_cmds(struct ssd130x_device *ssd130x, const u8 *cmd,
> size_t len)
> @@ -271,6 +310,17 @@ static int ssd130x_write_cmds(struct ssd130x_device
> *ssd130x, const u8 *cmd,
> unsigned int i;
> int ret;
>
> + if (ssd130x->device_info->cmd_params_are_data) {
> + if (!len)
> + return 0;
> +
Can len even be 0? If that's the case then I guess that makes more sense
to check and bail out early regardless if cmd_params_are_data is true ?
For the !cmd_params_are_data case, the for loop will be a no-op anyways
but still I think is cleaner to check as the first thing in this function.
> + ret = regmap_write(ssd130x->regmap, SSD13XX_COMMAND, cmd[0]);
> + if (ret || len == 1)
> + return ret;
> +
The len == 1 case is for commands that do not have parameters right? I
think that adding some comments explaining this to make it clear why
there is an early return.
I'm happy with the implementation now, thanks a lot for bearing with
me and your patience iterating over this series.
Reviewed-by: Javier Martinez Canillas <[email protected]>
--
Best regards,
Javier Martinez Canillas
Core Platforms
Red Hat
