On Thu, Sep 11, 2025 at 09:53:19AM +0200, Maud Spierings via B4 Relay wrote:
> diff --git a/drivers/video/backlight/max25014.c
> b/drivers/video/backlight/max25014.c
> new file mode 100644
> index
> 0000000000000000000000000000000000000000..f4ca79dfc39ccb04702e6114c35a5863f80b8853
> --- /dev/null
> +++ b/drivers/video/backlight/max25014.c
> @@ -0,0 +1,394 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Backlight driver for Maxim MAX25014
> + *
> + * Copyright (C) 2025 GOcontroll B.V.
> + * Author: Maud Spierings <maudspieri...@gocontroll.com>
> + */
> +
> +#include <linux/backlight.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +
> +#define MAX25014_ISET_DEFAULT_100 11
> +#define MAX_BRIGHTNESS 100
> +#define MIN_BRIGHTNESS 0
> +#define TON_MAX 130720 /* @153Hz */
> +#define TON_STEP 1307 /* @153Hz */
> +#define TON_MIN 0
> +
> +#define MAX25014_DEV_ID 0x00
> +#define MAX25014_REV_ID 0x01
> +#define MAX25014_ISET 0x02
> +#define MAX25014_IMODE 0x03
> +#define MAX25014_TON1H 0x04
> +#define MAX25014_TON1L 0x05
> +#define MAX25014_TON2H 0x06
> +#define MAX25014_TON2L 0x07
> +#define MAX25014_TON3H 0x08
> +#define MAX25014_TON3L 0x09
> +#define MAX25014_TON4H 0x0A
> +#define MAX25014_TON4L 0x0B
> +#define MAX25014_TON_1_4_LSB 0x0C
> +#define MAX25014_SETTING 0x12
> +#define MAX25014_DISABLE 0x13
> +#define MAX25014_BSTMON 0x14
> +#define MAX25014_IOUT1 0x15
> +#define MAX25014_IOUT2 0x16
> +#define MAX25014_IOUT3 0x17
> +#define MAX25014_IOUT4 0x18
> +#define MAX25014_OPEN 0x1B
> +#define MAX25014_SHORT_GND 0x1C
> +#define MAX25014_SHORT_LED 0x1D
> +#define MAX25014_MASK 0x1E
> +#define MAX25014_DIAG 0x1F
> +
> +#define MAX25014_IMODE_HDIM BIT(2)
> +#define MAX25014_ISET_ENABLE BIT(5)
> +#define MAX25014_ISET_PSEN BIT(4)
> +#define MAX25014_DIAG_HW_RST BIT(2)
> +#define MAX25014_SETTING_FPWM GENMASK(6, 4)
> +
> +struct max25014 {
> + struct i2c_client *client;
> + struct backlight_device *bl;
> + struct regmap *regmap;
> + struct gpio_desc *enable;
> + struct regulator *vin; /* regulator for boost converter Vin rail */
> + uint32_t iset;
> + uint8_t strings_mask;
> +};
> +
> +static const struct regmap_config max25014_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .max_register = MAX25014_DIAG,
> +};
> +
> +/**
> + * @brief control the brightness with i2c registers
> + *
> + * @param regmap trivial
> + * @param brt brightness
> + * @return int
> + */
> +static int max25014_register_control(struct regmap *regmap, uint32_t brt)
> +{
> + uint32_t reg = TON_STEP * brt;
> + int ret;
> + /*
> + * 18 bit number lowest, 2 bits in first register,
> + * next lowest 8 in the L register, next 8 in the H register
> + * Seemingly setting the strength of only one string controls all of
> + * them, individual settings don't affect the outcome.
> + */
> +
> + ret = regmap_write(regmap, MAX25014_TON_1_4_LSB, reg & 0b00000011);
> + if (ret != 0)
> + return ret;
> + ret = regmap_write(regmap, MAX25014_TON1L, (reg >> 2) & 0b11111111);
> + if (ret != 0)
> + return ret;
> + return regmap_write(regmap, MAX25014_TON1H, (reg >> 10) & 0b11111111);
> +}
> +
> +static int max25014_check_errors(struct max25014 *maxim)
> +{
> + uint8_t i;
> + int ret;
> + uint32_t val;
> +
> + ret = regmap_read(maxim->regmap, MAX25014_OPEN, &val);
> + if (ret != 0)
> + return ret;
> + if (val > 0) {
> + dev_err(&maxim->client->dev, "Open led strings detected on:\n");
> + for (i = 0; i < 4; i++) {
> + if (val & 1 << i)
> + dev_err(&maxim->client->dev, "string %d\n", i +
> 1);
> + }
> + return -EIO;
> + }
> +
> + ret = regmap_read(maxim->regmap, MAX25014_SHORT_GND, &val);
> + if (ret != 0)
> + return ret;
> + if (val > 0) {
> + dev_err(&maxim->client->dev, "Short to ground detected on:\n");
> + for (i = 0; i < 4; i++) {
> + if (val & 1 << i)
> + dev_err(&maxim->client->dev, "string %d\n", i +
> 1);
> + }
> + return -EIO;
> + }
> +
> + ret = regmap_read(maxim->regmap, MAX25014_SHORT_GND, &val);
> + if (ret != 0)
> + return ret;
> + if (val > 0) {
> + dev_err(&maxim->client->dev, "Shorted led detected on:\n");
> + for (i = 0; i < 4; i++) {
> + if (val & 1 << i)
> + dev_err(&maxim->client->dev, "string %d\n", i +
> 1);
> + }
> + return -EIO;
> + }
> +
> + ret = regmap_read(maxim->regmap, MAX25014_DIAG, &val);
> + if (ret != 0)
> + return ret;
> + /*
> + * The HW_RST bit always starts at 1 after power up.
> + * It is reset on first read, does not indicate an error.
> + */
> + if (val > 0 && val != MAX25014_DIAG_HW_RST) {
> + if (val & 0b1)
> + dev_err(&maxim->client->dev, "Overtemperature
> shutdown\n");
> + if (val & 0b10)
> + dev_warn(&maxim->client->dev,
> + "Chip is getting too hot (>125C)\n");
The dev_warn() looks a bit odd here. Even through the hardware is alive
the drive reacts to this warning by refusing to probe.
That problem means this should be dev_err() like all the other issues
here.
> + if (val & 0b1000)
> + dev_err(&maxim->client->dev, "Boost converter
> overvoltage\n");
> + if (val & 0b10000)
> + dev_err(&maxim->client->dev, "Boost converter
> undervoltage\n");
> + if (val & 0b100000)
> + dev_err(&maxim->client->dev, "IREF out of range\n");
> + return -EIO;
> + }
> + return 0;
> +}
> +
> +/*
> + * 1. disable unused strings
> + * 2. set dim mode
> + * 3. set initial brightness
> + * 4. set setting register
> + * 5. enable the backlight
> + */
> +static int max25014_configure(struct max25014 *maxim, uint32_t
> initial_brightness)
> +{
> + int ret;
> + uint32_t val;
> +
> + ret = regmap_write(maxim->regmap, MAX25014_DISABLE,
> + maxim->strings_mask);
> + if (ret != 0)
> + return ret;
> +
> + ret = regmap_write(maxim->regmap, MAX25014_IMODE, MAX25014_IMODE_HDIM);
> + if (ret != 0)
> + return ret;
> +
> + max25014_register_control(maxim->regmap,
> + initial_brightness);
> +
> + ret = regmap_read(maxim->regmap, MAX25014_SETTING, &val);
> + if (ret != 0)
> + return ret;
> +
> + ret = regmap_write(
> + maxim->regmap, MAX25014_SETTING,
> + val & ~MAX25014_SETTING_FPWM);
> + if (ret != 0)
> + return ret;
> +
> + ret = regmap_write(maxim->regmap, MAX25014_ISET,
> + maxim->iset | MAX25014_ISET_ENABLE |
> MAX25014_ISET_PSEN);
> + return ret;
> +}
> +
> +static int max25014_update_status(struct backlight_device *bl_dev)
> +{
> + struct max25014 *maxim = bl_get_data(bl_dev);
> +
> + if (bl_dev->props.state & BL_CORE_SUSPENDED)
> + bl_dev->props.brightness = 0;
This should be using the backlight_is_blank() helper rather than
fiddling with the state variables.
> +
> + return max25014_register_control(maxim->regmap,
> bl_dev->props.brightness);
> +}
> +
> +static const struct backlight_ops max25014_bl_ops = {
> + .options = BL_CORE_SUSPENDRESUME,
> + .update_status = max25014_update_status,
> +};
> +
> +static int max25014_parse_dt(struct max25014 *maxim, uint32_t
> *initial_brightness)
> +{
> + struct device *dev = &maxim->client->dev;
> + struct device_node *node = dev->of_node;
> + uint32_t strings[4];
> + int res, i;
> +
> + if (!node) {
> + dev_err(dev, "no platform data\n");
> + return -EINVAL;
> + }
> +
> + res = of_property_count_u32_elems(node, "maxim,strings");
> + if (res == 4) {
> + of_property_read_u32_array(node, "maxim,strings", strings, 4);
> + } else {
> + dev_err(dev, "strings property not correctly defined\n");
> + return -EINVAL;
> + }
> +
> + for (i = 0; i < 4; i++) {
> + if (strings[i] == 0)
> + maxim->strings_mask |= 1 << i;
> + }
> +
> + *initial_brightness = 50U;
> + of_property_read_u32(node, "default-brightness", initial_brightness);
> + maxim->iset = MAX25014_ISET_DEFAULT_100;
> + of_property_read_u32(node, "maxim,iset", &maxim->iset);
> +
> + if (maxim->iset < 0 || maxim->iset > 15) {
> + dev_err(dev,
> + "Invalid iset, should be a value from 0-15, entered was
> %d\n",
> + maxim->iset);
> + return -EINVAL;
> + }
> +
> + if (*initial_brightness < 0 || *initial_brightness > 100) {
> + dev_err(dev,
> + "Invalid initial brightness, should be a value from
> 0-100, entered was %d\n",
> + *initial_brightness);
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int max25014_probe(struct i2c_client *cl)
> +{
> + struct backlight_device *bl;
> + const struct i2c_device_id *id = i2c_client_get_device_id(cl);
> + struct max25014 *maxim;
> + struct backlight_properties props;
> + int ret;
> + uint32_t initial_brightness;
> +
> + maxim = devm_kzalloc(&cl->dev, sizeof(struct max25014), GFP_KERNEL);
> + if (!maxim)
> + return -ENOMEM;
> +
> + maxim->client = cl;
> +
> + ret = max25014_parse_dt(maxim, &initial_brightness);
> + if (ret < 0)
> + return ret;
> +
> + maxim->vin = devm_regulator_get(&maxim->client->dev, "power");
> + if (IS_ERR(maxim->vin)) {
> + if (PTR_ERR(maxim->vin) == -EPROBE_DEFER)
> + return -EPROBE_DEFER;
> + maxim->vin = NULL;
> + }
> +
> + if (maxim->vin) {
> + ret = regulator_enable(maxim->vin);
> + if (ret < 0) {
> + dev_err(&maxim->client->dev, "failed to enable Vin:
> %d\n", ret);
> + return ret;
> + }
> + }
> +
> + maxim->enable =
> + devm_gpiod_get_optional(&maxim->client->dev, "enable",
> GPIOD_ASIS);
> + if (IS_ERR(maxim->enable)) {
> + ret = PTR_ERR(maxim->enable);
> + dev_err(&maxim->client->dev, "failed to get enable gpio: %d\n",
> ret);
> + goto disable_vin;
> + }
> +
> + if (maxim->enable) {
> + gpiod_set_value_cansleep(maxim->enable, 1);
> +
> + /* Datasheet Electrical Characteristics tSTARTUP 2ms */
> + usleep_range(2000, 2500);
> + }
> +
> + maxim->regmap = devm_regmap_init_i2c(cl, &max25014_regmap_config);
> + if (IS_ERR(maxim->regmap)) {
> + ret = PTR_ERR(maxim->regmap);
> + dev_err(&maxim->client->dev, "failed to initialize the i2c
> regmap: %d\n", ret);
> + goto disable_full;
> + }
> +
> + i2c_set_clientdata(cl, maxim);
> +
> + ret = max25014_check_errors(maxim);
> + if (ret) { /* error is already reported in the above function */
> + goto disable_full;
> + }
> +
> + ret = max25014_configure(maxim, initial_brightness);
> + if (ret) {
> + dev_err(&maxim->client->dev, "device config err: %d", ret);
> + goto disable_full;
> + }
> +
> + memset(&props, 0, sizeof(props));
> + props.type = BACKLIGHT_PLATFORM;
> + props.max_brightness = MAX_BRIGHTNESS;
Please ensure that props.scale is set to something better than UNKNOWN.
Daniel.
