On 12.06.2025 07:49, Tomi Valkeinen wrote:
> On 11/06/2025 13:45, Marek Szyprowski wrote:
>> On 05.06.2025 19:15, Aradhya Bhatia wrote:
>>> From: Aradhya Bhatia <a-bhat...@ti.com>
>>>
>>> Move the bridge pre_enable call before crtc enable, and the bridge
>>> post_disable call after the crtc disable.
>>>
>>> The sequence of enable after this patch will look like:
>>>
>>> bridge[n]_pre_enable
>>> ...
>>> bridge[1]_pre_enable
>>>
>>> crtc_enable
>>> encoder_enable
>>>
>>> bridge[1]_enable
>>> ...
>>> bridge[n]_enable
>>>
>>> And, the disable sequence for the display pipeline will look like:
>>>
>>> bridge[n]_disable
>>> ...
>>> bridge[1]_disable
>>>
>>> encoder_disable
>>> crtc_disable
>>>
>>> bridge[1]_post_disable
>>> ...
>>> bridge[n]_post_disable
>>>
>>> The definition of bridge pre_enable hook says that,
>>> "The display pipe (i.e. clocks and timing signals) feeding this bridge
>>> will not yet be running when this callback is called".
>>>
>>> Since CRTC is also a source feeding the bridge, it should not be enabled
>>> before the bridges in the pipeline are pre_enabled. Fix that by
>>> re-ordering the sequence of bridge pre_enable and bridge post_disable.
>>>
>>> While at it, update the drm bridge API documentation as well.
>>>
>>> Acked-by: Dmitry Baryshkov <dmitry.barysh...@linaro.org>
>>> Reviewed-by: Tomi Valkeinen <tomi.valkei...@ideasonboard.com>
>>> Reviewed-by: Thomas Zimmermann <tzimmerm...@suse.de>
>>> Tested-by: Tomi Valkeinen <tomi.valkei...@ideasonboard.com>
>>> Tested-by: Alexander Sverdlin <alexander.sverd...@siemens.com>
>>> Signed-off-by: Aradhya Bhatia <a-bhat...@ti.com>
>>> Signed-off-by: Aradhya Bhatia <aradhya.bha...@linux.dev>
>> This patch landed in today's linux-next as commit c9b1150a68d9
>> ("drm/atomic-helper: Re-order bridge chain pre-enable and
>> post-disable"). In my tests I found that it breaks booting of Samsung
>> Exynos 5420/5800 based Chromebooks (Peach-Pit and Peach-Pi). Both of
>> them use Exynos DRM with Exynos_DP sub-driver (Analogix DP) and EDP
>> panel. Booting stops at '[drm] Initialized exynos 1.1.0 for exynos-drm
>> on minor 0' message. On the other hand, the Samsung Exynos5250 based
>> Snow Chromebook boots fine, but it uses dp-lvds nxp,ptn3460 bridge and
>> lvds panel instead of edp panels. This looks like some sort of deadlock,
>> because if I disable FBDEV emulation, those boards boots fine and I'm
>> able to run modetest and enable the display. Also the DRM kernel logger
>> seems to be working fine, although I didn't check the screen output yet,
>> as I only have a remote access to those boards. I will investigate it
>> further and let You know.
> Thanks for the report. I was trying to understand the pipeline, but I'm
> a bit confused. Above you say Peach-Pit uses DP and EDP panel, but if I
> look at arch/arm/boot/dts/samsung/exynos5420-peach-pit.dts, it connects
> a dp->lvds bridge (parade,ps8625). Peach-Pi seems to connect to an eDP
> panel.
>
> Is the above correct? Do both Peach-Pi and Peach-Pit fail?
Yes, sorry, my fault. I much have checked the same (peach-pi) dts 2
times. Both Peach-Pi and Peach-Pit fails, while Snow works fine. All
three use the same Exynos DP (based on analogix dp) driver. I will try
to play a bit more with those boards in the afternoon, hopefully getting
some more hints where the issue is.
Best regards
--
Marek Szyprowski, PhD
Samsung R&D Institute Poland
