On Wed, Feb 26, 2025 at 08:25:50PM +0900, Hironori KIKUCHI wrote:
> +
> +struct panel_firmware_header {
> + u8 magic[15];
> + u8 file_format_version; /* must be 1 */
> +} __packed;
> +
> +struct panel_firmware_config {
> + u16 width_mm, height_mm;
> + u16 rotation;
> + u8 _reserved_1[2];
> + u8 _reserved_2[8];
> +
> + u16 reset_delay; /* delay after the reset command, in ms */
> + u16 init_delay; /* delay for sending the initial command sequence, in
> ms */
> + u16 sleep_delay; /* delay after the sleep command, in ms */
> + u16 backlight_delay; /* delay for enabling the backlight, in ms */
These should be implied by compatible.
> + u16 _reserved_3[4];
> +
> + u16 dsi_lanes; /* unsigned int */
> + u16 dsi_format; /* enum mipi_dsi_pixel_format */
> + u32 dsi_mode_flags; /* unsigned long */
> + u32 bus_flags; /* struct drm_bus_flags */
> + u8 _reserved_4[2];
> + u8 preferred_timing;
> + u8 num_timings;
> +} __packed;
> +
...
> +
> +static int panel_mipi_probe(struct device *dev, int connector_type)
> +{
> + struct panel_mipi *mipi;
> + int err;
> +
> + mipi = devm_kzalloc(dev, sizeof(*mipi), GFP_KERNEL);
> + if (!mipi)
> + return -ENOMEM;
> +
> + mutex_init(&mipi->lock);
> +
> + mipi->display_id = -1;
> +
> + /* Get `power-supply` and `io-supply` (if any) */
> + mipi->supplies[0].supply = "power";
> + mipi->supplies[1].supply = "io";
> + err = devm_regulator_bulk_get(dev, ARRAY_SIZE(mipi->supplies),
> + mipi->supplies);
> + if (err < 0) {
> + return dev_err_probe(dev, err,
> + "%pOF: Failed to get regulators\n",
> + dev->of_node);
Drop pOF. Device name already tells this.
> + }
> +
> + /* GPIO for /RESET */
> + mipi->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
> + if (IS_ERR(mipi->reset))
> + return dev_err_probe(dev, PTR_ERR(mipi->reset),
> + "%pOF: Failed to get GPIO for RESET\n",
Drop pOF. Device name already tells this.
> + dev->of_node);
> +
> + /* Load the firmware */
> + mipi->firmware = panel_mipi_load_firmware(dev);
> + if (IS_ERR(mipi->firmware))
> + return dev_err_probe(dev, PTR_ERR(mipi->firmware),
> + "Failed to load firmware\n");
> +
> + err = panel_mipi_read_firmware(dev, mipi, mipi->firmware);
> + if (err)
> + return err;
> +
> + err = panel_mipi_probe_modes(dev, mipi);
> + if (err)
> + return err;
> +
> + /* DRM panel setup */
> + drm_panel_init(&mipi->panel, dev, &panel_mipi_funcs, connector_type);
> +
> + err = panel_mipi_set_backlight(&mipi->panel, dev, mipi);
> + if (err)
> + return dev_err_probe(dev, err, "Failed to set backlight\n");
> +
> + drm_panel_add(&mipi->panel);
> +
> + dev_set_drvdata(dev, mipi);
> +
> + panel_mipi_debugfs_init(dev, mipi);
> +
> + return devm_add_action_or_reset(dev, panel_mipi_cleanup, mipi);
> +}
> +
> +static int panel_mipi_dsi_probe(struct mipi_dsi_device *dsi)
> +{
> + struct panel_mipi *mipi;
> + int err;
> +
> + err = panel_mipi_probe(&dsi->dev, DRM_MODE_CONNECTOR_DSI);
> + if (err)
> + return err;
> +
> + mipi = dev_get_drvdata(&dsi->dev);
> + mipi->dsi = dsi;
> + mipi->write_command = panel_mipi_dsi_write;
> + mipi->read_command = panel_mipi_dsi_read;
> +
> + /* Read from the firmware */
> + dsi->lanes = be16_to_cpu(mipi->firmware->config->dsi_lanes);
lanes are from DT, because they are depending on how panel is wired. At
least usually.
> + dsi->format = be16_to_cpu(mipi->firmware->config->dsi_format);
> + dsi->mode_flags = be32_to_cpu(mipi->firmware->config->dsi_mode_flags);
> +
> + if (!dsi->lanes)
> + return dev_err_probe(&dsi->dev, -EINVAL,
> + "dsi-lanes == 0 for DSI panel\n");
> +
> + /* Adjust bus_format */
> + switch (dsi->format) {
> + case MIPI_DSI_FMT_RGB888:
> + mipi->bus_format = MEDIA_BUS_FMT_RGB888_1X24;
> + break;
> + case MIPI_DSI_FMT_RGB666:
> + mipi->bus_format = MEDIA_BUS_FMT_RGB666_1X24_CPADHI;
> + break;
> + case MIPI_DSI_FMT_RGB666_PACKED:
> + mipi->bus_format = MEDIA_BUS_FMT_RGB666_1X18;
> + break;
> + case MIPI_DSI_FMT_RGB565:
> + mipi->bus_format = MEDIA_BUS_FMT_RGB565_1X16;
> + break;
> + }
Best regards,
Krzysztof
