Hi Randy, Thanks for the patch!
On 07/12/23 11:52, Randy Dunlap wrote: > A few of the DRM_PANEL entries have become out of alphabetical order, > so move them around a bit to restore alpha order. > > Signed-off-by: Randy Dunlap <rdun...@infradead.org> > Cc: Neil Armstrong <neil.armstr...@linaro.org> > Cc: Jessica Zhang <quic_jessz...@quicinc.com> > Cc: Sam Ravnborg <s...@ravnborg.org> > Cc: Maarten Lankhorst <maarten.lankho...@linux.intel.com> > Cc: Maxime Ripard <mrip...@kernel.org> > Cc: Thomas Zimmermann <tzimmerm...@suse.de> > Cc: David Airlie <airl...@gmail.com> > Cc: Daniel Vetter <dan...@ffwll.ch> > Cc: dri-devel@lists.freedesktop.org > --- > drivers/gpu/drm/panel/Kconfig | 90 ++++++++++++++++---------------- > 1 file changed, 45 insertions(+), 45 deletions(-) > > diff -- a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig > --- a/drivers/gpu/drm/panel/Kconfig > +++ b/drivers/gpu/drm/panel/Kconfig > @@ -95,34 +95,6 @@ config DRM_PANEL_LVDS > handling of power supplies or control signals. It implements automatic > backlight handling if the panel is attached to a backlight controller. > > -config DRM_PANEL_SIMPLE > - tristate "support for simple panels (other than eDP ones)" > - depends on OF > - depends on BACKLIGHT_CLASS_DEVICE > - depends on PM > - select VIDEOMODE_HELPERS > - help > - DRM panel driver for dumb non-eDP panels that need at most a regulator > - and a GPIO to be powered up. Optionally a backlight can be attached so > - that it can be automatically turned off when the panel goes into a > - low power state. > - > -config DRM_PANEL_EDP > - tristate "support for simple Embedded DisplayPort panels" > - depends on OF > - depends on BACKLIGHT_CLASS_DEVICE > - depends on PM > - select VIDEOMODE_HELPERS > - select DRM_DISPLAY_DP_HELPER > - select DRM_DISPLAY_HELPER > - select DRM_DP_AUX_BUS > - select DRM_KMS_HELPER > - help > - DRM panel driver for dumb eDP panels that need at most a regulator and > - a GPIO to be powered up. Optionally a backlight can be attached so > - that it can be automatically turned off when the panel goes into a > - low power state. > - > config DRM_PANEL_EBBG_FT8719 > tristate "EBBG FT8719 panel driver" > depends on OF > @@ -317,12 +289,6 @@ config DRM_PANEL_LEADTEK_LTK500HD1829 > 24 bit RGB per pixel. It provides a MIPI DSI interface to > the host and has a built-in LED backlight. > > -config DRM_PANEL_SAMSUNG_LD9040 > - tristate "Samsung LD9040 RGB/SPI panel" > - depends on OF && SPI > - depends on BACKLIGHT_CLASS_DEVICE > - select VIDEOMODE_HELPERS > - > config DRM_PANEL_LG_LB035Q02 > tristate "LG LB035Q024573 RGB panel" > depends on GPIOLIB && OF && SPI > @@ -350,6 +316,17 @@ config DRM_PANEL_MAGNACHIP_D53E6EA8966 > with the Magnachip D53E6EA8966 panel IC. This panel receives > video data via DSI but commands via 9-bit SPI using DBI. > > +config DRM_PANEL_MANTIX_MLAF057WE51 > + tristate "Mantix MLAF057WE51-X MIPI-DSI LCD panel" > + depends on OF > + depends on DRM_MIPI_DSI > + depends on BACKLIGHT_CLASS_DEVICE > + help > + Say Y here if you want to enable support for the Mantix > + MLAF057WE51-X MIPI DSI panel as e.g. used in the Librem 5. It > + has a resolution of 720x1440 pixels, a built in backlight and touch > + controller. > + > config DRM_PANEL_NEC_NL8048HL11 > tristate "NEC NL8048HL11 RGB panel" > depends on GPIOLIB && OF && SPI > @@ -438,17 +415,6 @@ config DRM_PANEL_NOVATEK_NT39016 > Say Y here if you want to enable support for the panels built > around the Novatek NT39016 display controller. > > -config DRM_PANEL_MANTIX_MLAF057WE51 > - tristate "Mantix MLAF057WE51-X MIPI-DSI LCD panel" > - depends on OF > - depends on DRM_MIPI_DSI > - depends on BACKLIGHT_CLASS_DEVICE > - help > - Say Y here if you want to enable support for the Mantix > - MLAF057WE51-X MIPI DSI panel as e.g. used in the Librem 5. It > - has a resolution of 720x1440 pixels, a built in backlight and touch > - controller. > - > config DRM_PANEL_OLIMEX_LCD_OLINUXINO > tristate "Olimex LCD-OLinuXino panel" > depends on OF > @@ -566,6 +532,12 @@ config DRM_PANEL_SAMSUNG_DB7430 > DB7430 DPI display controller used in such devices as the > LMS397KF04 480x800 DPI panel. > > +config DRM_PANEL_SAMSUNG_LD9040 > + tristate "Samsung LD9040 RGB/SPI panel" > + depends on OF && SPI > + depends on BACKLIGHT_CLASS_DEVICE > + select VIDEOMODE_HELPERS > + > config DRM_PANEL_SAMSUNG_S6D16D0 > tristate "Samsung S6D16D0 DSI video mode panel" > depends on OF > @@ -774,6 +746,34 @@ config DRM_PANEL_STARTEK_KD070FHFID015 > with a resolution of 1024 x 600 pixels. It provides a MIPI DSI > interface to > the host, a built-in LED backlight and touch controller. > > +config DRM_PANEL_EDP > + tristate "support for simple Embedded DisplayPort panels" > + depends on OF > + depends on BACKLIGHT_CLASS_DEVICE > + depends on PM > + select VIDEOMODE_HELPERS > + select DRM_DISPLAY_DP_HELPER > + select DRM_DISPLAY_HELPER > + select DRM_DP_AUX_BUS > + select DRM_KMS_HELPER > + help > + DRM panel driver for dumb eDP panels that need at most a regulator and > + a GPIO to be powered up. Optionally a backlight can be attached so > + that it can be automatically turned off when the panel goes into a > + low power state. > + I don't think you intended to put PANEL_EDP this down the file! But just in case if you did, why? Regards Aradhya > +config DRM_PANEL_SIMPLE > + tristate "support for simple panels (other than eDP ones)" > + depends on OF > + depends on BACKLIGHT_CLASS_DEVICE > + depends on PM > + select VIDEOMODE_HELPERS > + help > + DRM panel driver for dumb non-eDP panels that need at most a regulator > + and a GPIO to be powered up. Optionally a backlight can be attached so > + that it can be automatically turned off when the panel goes into a > + low power state. > + > config DRM_PANEL_TDO_TL070WSH30 > tristate "TDO TL070WSH30 DSI panel" > depends on OF
