On Wed, Dec 07, 2022 at 02:00:11PM -0800, Bjorn Andersson wrote:
> From: Bjorn Andersson <bjorn.anders...@linaro.org>
>
> The SC8280XP CRD has a EDP display on MDSS0 DP3, enable relevant nodes
> and link it together with the backlight control.
>
> Signed-off-by: Bjorn Andersson <bjorn.anders...@linaro.org>
> Signed-off-by: Bjorn Andersson <quic_bjora...@quicinc.com>
> ---
>
> Changes since v4:
> - None
>
> arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 72 ++++++++++++++++++++++-
> 1 file changed, 71 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> index f09810e3d956..a7d2384cbbe8 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> @@ -20,7 +20,7 @@ aliases {
> serial0 = &qup2_uart17;
> };
>
> - backlight {
> + backlight: backlight {
> compatible = "pwm-backlight";
> pwms = <&pmc8280c_lpg 3 1000000>;
> enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>;
> @@ -34,6 +34,22 @@ chosen {
> stdout-path = "serial0:115200n8";
> };
>
> + vreg_edp_3p3: regulator-edp-3p3 {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "VREG_EDP_3P3";
Please use the net name from the schematics here (i.e. "VCC3LCD").
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&edp_reg_en>;
> +
> + regulator-boot-on;
> + };
> +
> vreg_edp_bl: regulator-edp-bl {
> compatible = "regulator-fixed";
>
> @@ -230,6 +246,54 @@ vreg_l9d: ldo9 {
> };
> };
>
> +&dispcc0 {
> + status = "okay";
> +};
> +
> +&mdss0 {
> + status = "okay";
> +};
> +
> +&mdss0_dp3 {
> + compatible = "qcom,sc8280xp-edp";
> + status = "okay";
Please move the status property last (i.e. after data-lanes).
> +
> + data-lanes = <0 1 2 3>;
> +
> + aux-bus {
> + panel {
> + compatible = "edp-panel";
> + power-supply = <&vreg_edp_3p3>;
> +
> + backlight = <&backlight>;
> +
> + ports {
> + port {
> + edp_panel_in: endpoint {
> + remote-endpoint =
> <&mdss0_dp3_out>;
> + };
> + };
> + };
> + };
> + };
> +
> + ports {
> + port@1 {
> + reg = <1>;
> + mdss0_dp3_out: endpoint {
> + remote-endpoint = <&edp_panel_in>;
> + };
> + };
> + };
> +};
> +
> +&mdss0_dp3_phy {
> + status = "okay";
Same here.
> +
> + vdda-phy-supply = <&vreg_l6b>;
> + vdda-pll-supply = <&vreg_l3b>;
> +};
> +
> &pcie2a {
> perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
> wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
> @@ -496,6 +560,12 @@ hastings_reg_en: hastings-reg-en-state {
> &tlmm {
> gpio-reserved-ranges = <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
>
> + edp_reg_en: edp-reg-en-state {
> + pins = "gpio25";
> + function = "gpio";
> + output-enable;
'output-enable' is not valid for tlmm and causes the settings to be
rejected:
sc8280xp-tlmm f100000.pinctrl: pin_config_group_set op failed for group
25
reg-fixed-voltage regulator-edp-3p3: Error applying setting, reverse
things back
> + };
> +
> kybd_default: kybd-default-state {
> disable-pins {
> pins = "gpio102";
Johan
