Rather than reading the pdata->connector directly, fetch the connector
using drm_atomic_state. This allows us to make pdata->connector optional
(and thus supporting DRM_BRIDGE_ATTACH_NO_CONNECTOR).
Reviewed-by: Sam Ravnborg <s...@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinch...@ideasonboard.com>
Signed-off-by: Dmitry Baryshkov <dmitry.barysh...@linaro.org>
---
drivers/gpu/drm/bridge/ti-sn65dsi86.c | 22 ++++++++++++++++------
1 file changed, 16 insertions(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi86.c
b/drivers/gpu/drm/bridge/ti-sn65dsi86.c
index d6dd4d99a229..b362a7bf4d97 100644
--- a/drivers/gpu/drm/bridge/ti-sn65dsi86.c
+++ b/drivers/gpu/drm/bridge/ti-sn65dsi86.c
@@ -779,9 +779,9 @@ static void ti_sn_bridge_set_dsi_rate(struct ti_sn65dsi86
*pdata)
regmap_write(pdata->regmap, SN_DSIA_CLK_FREQ_REG, val);
}
-static unsigned int ti_sn_bridge_get_bpp(struct ti_sn65dsi86 *pdata)
+static unsigned int ti_sn_bridge_get_bpp(struct drm_connector *connector)
{
- if (pdata->connector->display_info.bpc <= 6)
+ if (connector->display_info.bpc <= 6)
return 18;
else
return 24;
@@ -796,7 +796,7 @@ static const unsigned int ti_sn_bridge_dp_rate_lut[] = {
0, 1620, 2160, 2430, 2700, 3240, 4320, 5400
};
-static int ti_sn_bridge_calc_min_dp_rate_idx(struct ti_sn65dsi86 *pdata)
+static int ti_sn_bridge_calc_min_dp_rate_idx(struct ti_sn65dsi86 *pdata,
unsigned int bpp)
{
unsigned int bit_rate_khz, dp_rate_mhz;
unsigned int i;
@@ -804,7 +804,7 @@ static int ti_sn_bridge_calc_min_dp_rate_idx(struct
ti_sn65dsi86 *pdata)
&pdata->bridge.encoder->crtc->state->adjusted_mode;
/* Calculate minimum bit rate based on our pixel clock. */
- bit_rate_khz = mode->clock * ti_sn_bridge_get_bpp(pdata);
+ bit_rate_khz = mode->clock * bpp;
/* Calculate minimum DP data rate, taking 80% as per DP spec */
dp_rate_mhz = DIV_ROUND_UP(bit_rate_khz * DP_CLK_FUDGE_NUM,
@@ -1016,12 +1016,21 @@ static void ti_sn_bridge_atomic_enable(struct
drm_bridge *bridge,
struct drm_bridge_state
*old_bridge_state)
{
struct ti_sn65dsi86 *pdata = bridge_to_ti_sn65dsi86(bridge);
+ struct drm_connector *connector;
const char *last_err_str = "No supported DP rate";
unsigned int valid_rates;
int dp_rate_idx;
unsigned int val;
int ret = -EINVAL;
int max_dp_lanes;
+ unsigned int bpp;
+
+ connector =
drm_atomic_get_new_connector_for_encoder(old_bridge_state->base.state,
+ bridge->encoder);
+ if (!connector) {
+ dev_err_ratelimited(pdata->dev, "Could not get the
connector\n");
+ return;
+ }
max_dp_lanes = ti_sn_get_max_lanes(pdata);
pdata->dp_lanes = min(pdata->dp_lanes, max_dp_lanes);
@@ -1047,8 +1056,9 @@ static void ti_sn_bridge_atomic_enable(struct drm_bridge
*bridge,
drm_dp_dpcd_writeb(&pdata->aux, DP_EDP_CONFIGURATION_SET,
DP_ALTERNATE_SCRAMBLER_RESET_ENABLE);
+ bpp = ti_sn_bridge_get_bpp(connector);
/* Set the DP output format (18 bpp or 24 bpp) */
- val = (ti_sn_bridge_get_bpp(pdata) == 18) ? BPP_18_RGB : 0;
+ val = bpp == 18 ? BPP_18_RGB : 0;
regmap_update_bits(pdata->regmap, SN_DATA_FORMAT_REG, BPP_18_RGB, val);
/* DP lane config */
@@ -1059,7 +1069,7 @@ static void ti_sn_bridge_atomic_enable(struct drm_bridge
*bridge,
valid_rates = ti_sn_bridge_read_valid_rates(pdata);
/* Train until we run out of rates */
- for (dp_rate_idx = ti_sn_bridge_calc_min_dp_rate_idx(pdata);
+ for (dp_rate_idx = ti_sn_bridge_calc_min_dp_rate_idx(pdata, bpp);
dp_rate_idx < ARRAY_SIZE(ti_sn_bridge_dp_rate_lut);
dp_rate_idx++) {
if (!(valid_rates & BIT(dp_rate_idx)))
--
2.35.1
