From: Chen-Yu Tsai <w...@csie.org>
Currently the ssd130x driver only sets the segment remap setting when
the device tree requests it; it however does not clear the setting if
it is not requested. This leads to the setting incorrectly persisting
if the hardware is always on and has no reset GPIO wired. This might
happen when a developer is trying to find the correct settings for an
unknown module, and cause the developer to get confused because the
settings from the device tree are not consistently applied.
Make the driver apply the segment remap setting consistently, setting
the value correctly based on the device tree setting. This also makes
this setting's behavior consistent with the other settings, which are
always applied.
Fixes: a61732e80867 ("drm: Add driver for Solomon SSD130x OLED displays")
Signed-off-by: Chen-Yu Tsai <w...@csie.org>
---
drivers/gpu/drm/solomon/ssd130x.c | 16 +++++++++-------
1 file changed, 9 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/solomon/ssd130x.c
b/drivers/gpu/drm/solomon/ssd130x.c
index ccd378135589..d08d86ef07bc 100644
--- a/drivers/gpu/drm/solomon/ssd130x.c
+++ b/drivers/gpu/drm/solomon/ssd130x.c
@@ -48,7 +48,7 @@
#define SSD130X_CONTRAST 0x81
#define SSD130X_SET_LOOKUP_TABLE 0x91
#define SSD130X_CHARGE_PUMP 0x8d
-#define SSD130X_SEG_REMAP_ON 0xa1
+#define SSD130X_SET_SEG_REMAP 0xa0
#define SSD130X_DISPLAY_OFF 0xae
#define SSD130X_SET_MULTIPLEX_RATIO 0xa8
#define SSD130X_DISPLAY_ON 0xaf
@@ -61,6 +61,8 @@
#define SSD130X_SET_COM_PINS_CONFIG 0xda
#define SSD130X_SET_VCOMH 0xdb
+#define SSD130X_SET_SEG_REMAP_MASK GENMASK(0, 0)
+#define SSD130X_SET_SEG_REMAP_SET(val)
FIELD_PREP(SSD130X_SET_SEG_REMAP_MASK, (val))
#define SSD130X_SET_COM_SCAN_DIR_MASK GENMASK(3, 3)
#define SSD130X_SET_COM_SCAN_DIR_SET(val)
FIELD_PREP(SSD130X_SET_COM_SCAN_DIR_MASK, (val))
#define SSD130X_SET_CLOCK_DIV_MASK GENMASK(3, 0)
@@ -235,7 +237,7 @@ static void ssd130x_power_off(struct ssd130x_device
*ssd130x)
static int ssd130x_init(struct ssd130x_device *ssd130x)
{
- u32 precharge, dclk, com_invdir, compins, chargepump;
+ u32 precharge, dclk, com_invdir, compins, chargepump, seg_remap;
int ret;
/* Set initial contrast */
@@ -244,11 +246,11 @@ static int ssd130x_init(struct ssd130x_device *ssd130x)
return ret;
/* Set segment re-map */
- if (ssd130x->seg_remap) {
- ret = ssd130x_write_cmd(ssd130x, 1, SSD130X_SEG_REMAP_ON);
- if (ret < 0)
- return ret;
- }
+ seg_remap = (SSD130X_SET_SEG_REMAP |
+ SSD130X_SET_SEG_REMAP_SET(ssd130x->seg_remap));
+ ret = ssd130x_write_cmd(ssd130x, 1, seg_remap);
+ if (ret < 0)
+ return ret;
/* Set COM direction */
com_invdir = (SSD130X_SET_COM_SCAN_DIR |
--
2.34.1
