This driver will register a DBI host driver for panels connected over SPI. For now, only DBI type c3 is supported, which is a SPI protocol with 8 bits per word, with the data/command information carried by a separate GPIO.
Signed-off-by: Paul Cercueil <[email protected]> --- drivers/gpu/drm/bridge/Kconfig | 8 ++ drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/dbi-spi.c | 159 +++++++++++++++++++++++++++++++ 3 files changed, 168 insertions(+) create mode 100644 drivers/gpu/drm/bridge/dbi-spi.c diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig index aaed2347ace9..61587bc4d6e6 100644 --- a/drivers/gpu/drm/bridge/Kconfig +++ b/drivers/gpu/drm/bridge/Kconfig @@ -180,6 +180,14 @@ config DRM_TI_TPD12S015 Texas Instruments TPD12S015 HDMI level shifter and ESD protection driver. +config DRM_MIPI_DBI_SPI + tristate "SPI host support for MIPI DBI" + depends on OF && SPI + select DRM_MIPI_DSI + select DRM_MIPI_DBI + help + Driver to support DBI over SPI. + source "drivers/gpu/drm/bridge/analogix/Kconfig" source "drivers/gpu/drm/bridge/adv7511/Kconfig" diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile index 6fb062b5b0f0..17fdf7de498d 100644 --- a/drivers/gpu/drm/bridge/Makefile +++ b/drivers/gpu/drm/bridge/Makefile @@ -18,6 +18,7 @@ obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/ obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o obj-$(CONFIG_DRM_TI_TPD12S015) += ti-tpd12s015.o +obj-$(CONFIG_DRM_MIPI_DBI_SPI) += dbi-spi.o obj-y += analogix/ obj-y += synopsys/ diff --git a/drivers/gpu/drm/bridge/dbi-spi.c b/drivers/gpu/drm/bridge/dbi-spi.c new file mode 100644 index 000000000000..c790514b7372 --- /dev/null +++ b/drivers/gpu/drm/bridge/dbi-spi.c @@ -0,0 +1,159 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * MIPI Display Bus Interface (DBI) SPI support + * + * Copyright 2016 Noralf Trønnes + * Copyright 2020 Paul Cercueil <[email protected]> + */ + +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/spi/spi.h> + +#include <drm/drm_mipi_dbi.h> +#include <drm/drm_mipi_dsi.h> + +#include <video/mipi_display.h> + +struct dbi_spi { + struct mipi_dsi_host host; + struct mipi_dsi_host_ops host_ops; + + struct spi_device *spi; + struct gpio_desc *dc; + struct mutex cmdlock; +}; + +static inline struct dbi_spi *host_to_dbi_spi(struct mipi_dsi_host *host) +{ + return container_of(host, struct dbi_spi, host); +} + +static ssize_t dbi_spi_transfer(struct mipi_dsi_host *host, + const struct mipi_dsi_msg *msg) +{ + struct dbi_spi *dbi = host_to_dbi_spi(host); + struct spi_device *spi = dbi->spi; + const u8 *buf = msg->tx_buf; + unsigned int bpw = 8; + u32 speed_hz; + ssize_t ret; + + /* for now we only support sending messages, not receiving */ + if (msg->rx_len) + return -ENOTSUPP; + + gpiod_set_value_cansleep(dbi->dc, 0); + + speed_hz = mipi_dbi_spi_cmd_max_speed(spi, 1); + ret = mipi_dbi_spi_transfer(spi, speed_hz, 8, buf, 1); + if (ret || msg->tx_len == 1) + return ret; + + if (buf[0] == MIPI_DCS_WRITE_MEMORY_START) + bpw = 16; + + gpiod_set_value_cansleep(dbi->dc, 1); + speed_hz = mipi_dbi_spi_cmd_max_speed(spi, msg->tx_len - 1); + + ret = mipi_dbi_spi_transfer(spi, speed_hz, bpw, + &buf[1], msg->tx_len - 1); + if (ret) + return ret; + + return msg->tx_len; +} + +static int dbi_spi_attach(struct mipi_dsi_host *host, + struct mipi_dsi_device *dsi) +{ + return 0; /* Nothing to do */ +} + +static int dbi_spi_detach(struct mipi_dsi_host *host, + struct mipi_dsi_device *dsi) +{ + return 0; /* Nothing to do */ +} + +static void dbi_spi_host_unregister(void *d) +{ + mipi_dsi_host_unregister(d); +} + +static int dbi_spi_probe(struct spi_device *spi) +{ + struct device *dev = &spi->dev; + struct mipi_dsi_device_info info = { }; + struct mipi_dsi_device *dsi; + struct dbi_spi *dbi; + int ret; + + dbi = devm_kzalloc(dev, sizeof(*dbi), GFP_KERNEL); + if (!dbi) + return -ENOMEM; + + /* Only DBI Type C3 supported for now */ + dbi->host.bus_types = MIPI_DEVICE_TYPE_DBI_SPI_MODE3; + + dbi->host.dev = dev; + dbi->host.ops = &dbi->host_ops; + dbi->spi = spi; + spi_set_drvdata(spi, dbi); + + dbi->dc = devm_gpiod_get(dev, "dc", GPIOD_OUT_LOW); + if (IS_ERR(dbi->dc)) { + dev_err(dev, "Failed to get gpio 'dc'\n"); + return PTR_ERR(dbi->dc); + } + + dbi->host_ops.transfer = dbi_spi_transfer; + dbi->host_ops.attach = dbi_spi_attach; + dbi->host_ops.detach = dbi_spi_detach; + + mutex_init(&dbi->cmdlock); + + ret = mipi_dsi_host_register(&dbi->host); + if (ret) { + dev_err(dev, "Unable to register DSI host\n"); + return ret; + } + + ret = devm_add_action_or_reset(dev, dbi_spi_host_unregister, &dbi->host); + if (ret) + return ret; + + /* + * Register our own node as a MIPI DSI device. + * This ensures that the panel driver will be probed. + */ + info.channel = 0; + info.node = of_node_get(dev->of_node); + + dsi = mipi_dsi_device_register_full(&dbi->host, &info); + if (IS_ERR(dsi)) { + dev_err(dev, "Failed to add DSI device\n"); + return PTR_ERR(dsi); + } + + return 0; +} + +static const struct of_device_id dbi_spi_of_match[] = { + { .compatible = "adafruit,yx240qv29" }, + { } +}; +MODULE_DEVICE_TABLE(of, dbi_spi_of_match); + +static struct spi_driver dbi_spi_driver = { + .driver = { + .name = "dbi-spi", + .of_match_table = dbi_spi_of_match, + }, + .probe = dbi_spi_probe, +}; +module_spi_driver(dbi_spi_driver); + +MODULE_DESCRIPTION("DBI SPI bus driver"); +MODULE_AUTHOR("Paul Cercueil <[email protected]>"); +MODULE_LICENSE("GPL"); -- 2.26.2 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
