On Thu 23 Jan 04:15 PST 2020, Harigovindan P wrote:
> Add display, DSI hardware DT nodes for sc7180.
>
> Changes in v1:
> -Added display DT nodes for sc7180
> Changes in v2:
> -Renamed node names
> -Corrected code alignments
> -Removed extra new line
Please keep the changelist after the '---' for the dts patches.
>
> Signed-off-by: Harigovindan P <harig...@codeaurora.org>
> ---
> arch/arm64/boot/dts/qcom/sc7180-idp.dts | 57 +++++++++++++++
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 125
> ++++++++++++++++++++++++++++++++
> 2 files changed, 182 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> index 388f50a..f410614 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> @@ -232,6 +232,50 @@
> };
> };
>
> +&dsi_controller {
> + status = "okay";
> +
> + vdda-supply = <&vreg_l3c_1p2>;
> +
> + panel@0 {
> + compatible = "visionox,rm69299-1080p-display";
> + reg = <0>;
> +
> + vdda-supply = <&vreg_l8c_1p8>;
> + vdd3p3-supply = <&vreg_l18a_2p8>;
> +
> + pinctrl-names = "default", "suspend";
> + pinctrl-0 = <&disp_pins_default>;
> + pinctrl-1 = <&disp_pins_default>;
> +
> + reset-gpios = <&pm6150l_gpio 3 0>;
Please replace the 0 here with GPIO_ACTIVE_HIGH
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + port@0 {
> + reg = <0>;
> + panel0_in: endpoint {
> + remote-endpoint = <&dsi0_out>;
> + };
> + };
> + };
> + };
[..]
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 3bc3f64..81c3aab 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -1184,6 +1184,131 @@
> #power-domain-cells = <1>;
> };
>
> + display_subsystem: mdss@ae00000 {
It was the name, not the label, that Stephen asked you to make generic.
> + compatible = "qcom,sc7180-mdss";
> + reg = <0 0x0ae00000 0 0x1000>;
> + reg-names = "mdss";
> +
[..]
> + display_controller: mdp@ae00000 {
mdp: display-controller@ae00000 {
[..]
> + };
> +
> + dsi_controller: qcom,mdss_dsi_ctrl0@ae94000 {
In particular you shouldn't have qcom, in the node name.
[..]
> +
> + dsi_phy: dsi-phy0@ae94400 {
phy@ae94400
Regards,
Bjorn
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
