On Thu, Jan 09, 2020 at 05:38:15PM +0200, Ville Syrjälä wrote:
> On Thu, Jan 09, 2020 at 05:26:57PM +0200, Ville Syrjälä wrote:
> > On Thu, Jan 09, 2020 at 04:07:52PM +0100, Mario Kleiner wrote:
> > > If the current eDP link rate, as read from hw, provides a
> > > higher bandwidth than the standard link rates, then add the
> > > current link rate to the link_rates array for consideration
> > > in future mode-sets.
> > >
> > > These initial current eDP link settings have been set up by
> > > firmware during boot, so they should work on the eDP panel.
> > > Therefore use them if the firmware thinks they are good and
> > > they provide higher link bandwidth, e.g., to enable higher
> > > resolutions / color depths.
> > >
> > > This fixes a problem found on the MacBookPro 2017 Retina panel:
> > >
> > > The panel reports 10 bpc color depth in its EDID, and the UEFI
> > > firmware chooses link settings at boot which support enough
> > > bandwidth for 10 bpc (324000 kbit/sec to be precise), but the
> > > DP_MAX_LINK_RATE dpcd register only reports 2.7 Gbps as possible,
>
> Does it actually or do we just ignore the fact that it reports 3.24Gbps?
>
> If it really reports 3.24 then we should be able to just add that to
> dp_rates[] in intel_dp_set_sink_rates() and be done with it.
>
> Although we'd likely want to skip 3.24 unless it really is reported
> as the max so as to not use that non-standard rate on other displays.
> So would require a bit fancier logic for that.
Maybe just something like this?
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -177,6 +177,12 @@ static void intel_dp_set_sink_rates(struct intel_dp
*intel_dp)
intel_dp->sink_rates[i] = dp_rates[i];
}
+ /* blah */
+ if (max_rate > intel_dp->sink_rates[i - 1]) {
+ DRM_DEBUG_KMS(...);
+ intel_dp->sink_rates[i++] = max_rate;
+ }
+
intel_dp->num_sink_rates = i;
>
> > > so intel_dp_set_sink_rates() would cap at that. This restricts
> > > achievable color depth to 8 bpc, not providing the full color
> > > depth of the panel. With this commit, we can use firmware setting
> > > and get the full 10 bpc advertised by the Retina panel.
> > >
> > > Signed-off-by: Mario Kleiner <mario.kleiner...@gmail.com>
> > > Cc: Daniel Vetter <daniel.vet...@ffwll.ch>
> > > ---
> > > drivers/gpu/drm/i915/display/intel_dp.c | 23 +++++++++++++++++++++++
> > > 1 file changed, 23 insertions(+)
> > >
> > > diff --git a/drivers/gpu/drm/i915/display/intel_dp.c
> > > b/drivers/gpu/drm/i915/display/intel_dp.c
> > > index 2f31d226c6eb..aa3e0b5108c6 100644
> > > --- a/drivers/gpu/drm/i915/display/intel_dp.c
> > > +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> > > @@ -4368,6 +4368,8 @@ intel_edp_init_dpcd(struct intel_dp *intel_dp)
> > > {
> > > struct drm_i915_private *dev_priv =
> > > to_i915(dp_to_dig_port(intel_dp)->base.base.dev);
> > > + int max_rate;
> > > + u8 link_bw;
> > >
> > > /* this function is meant to be called only once */
> > > WARN_ON(intel_dp->dpcd[DP_DPCD_REV] != 0);
> > > @@ -4433,6 +4435,27 @@ intel_edp_init_dpcd(struct intel_dp *intel_dp)
> > > else
> > > intel_dp_set_sink_rates(intel_dp);
> > >
> > > + /*
> > > + * If the firmware programmed a rate higher than the standard sink rates
> > > + * during boot, then add that rate as a valid sink rate, as fw knows
> > > + * this is a good rate and we get extra bandwidth.
> > > + *
> > > + * Helps, e.g., on the Apple MacBookPro 2017 Retina panel, which is only
> > > + * eDP 1.1, but supports the unusual rate of 324000 kHz at bootup, for
> > > + * 10 bpc / 30 bit color depth.
> > > + */
> > > + if (!intel_dp->use_rate_select &&
> > > + (drm_dp_dpcd_read(&intel_dp->aux, DP_LINK_BW_SET, &link_bw, 1) ==
> > > 1) &&
> > > + (link_bw > 0) && (intel_dp->num_sink_rates <
> > > DP_MAX_SUPPORTED_RATES)) {
> > > + max_rate = drm_dp_bw_code_to_link_rate(link_bw);
> > > + if (max_rate > intel_dp->sink_rates[intel_dp->num_sink_rates -
> > > 1]) {
> > > + intel_dp->sink_rates[intel_dp->num_sink_rates] =
> > > max_rate;
> > > + intel_dp->num_sink_rates++;
> > > + DRM_DEBUG_KMS("Adding max bandwidth eDP rate %d kHz.\n",
> > > + max_rate);
> > > + }
> >
> > Hmm. I guess we could do this. But plese put it into a separate
> > function so we don't end up with that super ugly if condition.
> >
> > The debug message should probably be a bit more explicit. Eg.
> > something like:
> > "Firmware using non-standard link rate %d kHz. Including it in sink
> > rates.\n"
> >
> > I'm also wondering if we shouldn't just add the link rate to the sink
> > rates regradless of whether it's the highest rate or not...
> >
> > > + }
> > > +
> > > intel_dp_set_common_rates(intel_dp);
> > >
> > > /* Read the eDP DSC DPCD registers */
> > > --
> > > 2.24.0
> > >
> > > _______________________________________________
> > > dri-devel mailing list
> > > dri-devel@lists.freedesktop.org
> > > https://lists.freedesktop.org/mailman/listinfo/dri-devel
> >
> > --
> > Ville Syrjälä
> > Intel
>
> --
> Ville Syrjälä
> Intel
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
--
Ville Syrjälä
Intel
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
