Hi Jyri,
Thank you for the patch.
On Thu, Mar 14, 2019 at 01:27:51PM +0200, Jyri Sarha wrote:
> The sii902x chip family supports also HDMI audio. Add binding for
> describing the necessary i2s and mclk wiring for it.
>
> Signed-off-by: Jyri Sarha <jsa...@ti.com>
> ---
> .../bindings/display/bridge/sii902x.txt | 33 +++++++++++++++++++
> 1 file changed, 33 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt
> b/Documentation/devicetree/bindings/display/bridge/sii902x.txt
> index c4c1855ca654..1a37bbe7c597 100644
> --- a/Documentation/devicetree/bindings/display/bridge/sii902x.txt
> +++ b/Documentation/devicetree/bindings/display/bridge/sii902x.txt
> @@ -9,6 +9,33 @@ Optional properties:
> about hotplug events.
> - reset-gpios: OF device-tree gpio specification for RST_N pin.
>
> + HDMI audio properties:
> + - i2s-data-lanes: Array of up to 4 integers with values of 0-3
> + Each integer indicates which i2s pin is connected to which
> + audio fifo. The first integer selects i2s audio pin for the
> + first audio fifo#0 (HDMI channels 1&2), second for fifo#1
> + (HDMI channels 3&4), and so on. There is 4 fifos and 4 i2s
> + pins (SD0 - SD3). Any i2s pin can be connected to any fifo,
> + but there can be no gaps. E.g. an i2s pin must be mapped to
> + fifo#0 and fifo#1 before mapping a channel to fifo#2.
> + I2S HDMI audio is configured only if this property is found.
This looks good to me, but shouldn't the property be defined somewhere
in Documentation/devicetree/bindings/sound/ ? The sound bindings seem to
be a bit messy though, with little common or high-level documentation,
so I don't want to ask you to fix all that :-) Maybe just adding a
common-i2s.txt file there would be enough ?
Apart from this the rest looks good to me, but I'd appreciate if it
could be reviewed by audio people.
> + - clocks: phandle and clock specifier for each clock listed in
> + the clock-names property
> + - clock-names: "mclk"
> + Describes SII902x MCLK input. MCLK is used to produce
> + HDMI audio CTS values. This property is required if
> + "i2s-data-lanes"-property is present. This property follows
> + Documentation/devicetree/bindings/clock/clock-bindings.txt
> + consumer binding.
> +
> + If HDMI audio is configured the sii902x device becomes an ASoC
> + codec component, that can be used in configuring full audio
> + devices with ASoC simple-card or audio-graph-card. See their
> + binding documents on how to describe how the sii902x device is
> + connected to the rest of the audio system:
> + Documentation/devicetree/bindings/sound/simple-card.txt
> + Documentation/devicetree/bindings/sound/audio-graph-card.txt
> +
> Optional subnodes:
> - video input: this subnode can contain a video input port node
> to connect the bridge to a display controller output (See this
> @@ -21,6 +48,12 @@ Example:
> compatible = "sil,sii9022";
> reg = <0x39>;
> reset-gpios = <&pioA 1 0>;
> +
> + #sound-dai-cells = <0>;
> + i2s-data-lanes = < 0 1 2 >;
> + clocks = <&mclk>;
> + clock-names = "mclk";
> +
> ports {
> #address-cells = <1>;
> #size-cells = <0>;
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
