On Fri, Nov 23, 2018 at 10:24:59AM +0100, Paul Kocialkowski wrote:
> Semi-planar YUV formats use two distinct planes, one for luminance and
> one for chrominance. To add support for them, we need to configure the
> second line stride and buffer address registers to setup the second YUV
> plane.
>
> New definitions are introduced to configure the input format register
> for the YUV420 and YUV422 semi-planar formats.
>
> Signed-off-by: Paul Kocialkowski <paul.kocialkow...@bootlin.com>
> ---
> drivers/gpu/drm/sun4i/sun4i_frontend.c | 52 +++++++++++++++++++++++---
> drivers/gpu/drm/sun4i/sun4i_frontend.h | 6 +++
> drivers/gpu/drm/sun4i/sun4i_layer.c | 4 ++
> 3 files changed, 57 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/gpu/drm/sun4i/sun4i_frontend.c
> b/drivers/gpu/drm/sun4i/sun4i_frontend.c
> index f443e8e1d8ec..e31438e5cabd 100644
> --- a/drivers/gpu/drm/sun4i/sun4i_frontend.c
> +++ b/drivers/gpu/drm/sun4i/sun4i_frontend.c
> @@ -118,11 +118,23 @@ void sun4i_frontend_update_buffer(struct sun4i_frontend
> *frontend,
> regmap_write(frontend->regs, SUN4I_FRONTEND_LINESTRD0_REG,
> fb->pitches[0]);
>
> + if (fb->format->num_planes > 1)
> + regmap_write(frontend->regs, SUN4I_FRONTEND_LINESTRD1_REG,
> + fb->pitches[1]);
> +
> /* Set the physical address of the buffer in memory */
> paddr = drm_fb_cma_get_gem_addr(fb, state, 0);
> paddr -= PHYS_OFFSET;
> - DRM_DEBUG_DRIVER("Setting buffer address to %pad\n", &paddr);
> + DRM_DEBUG_DRIVER("Setting buffer #0 address to %pad\n", &paddr);
> regmap_write(frontend->regs, SUN4I_FRONTEND_BUF_ADDR0_REG, paddr);
> +
> + if (fb->format->num_planes > 1) {
> + paddr = drm_fb_cma_get_gem_addr(fb, state, 1);
> + paddr -= PHYS_OFFSET;
> + DRM_DEBUG_DRIVER("Setting buffer #1 address to %pad\n", &paddr);
> + regmap_write(frontend->regs, SUN4I_FRONTEND_BUF_ADDR1_REG,
> + paddr);
> + }
> }
> EXPORT_SYMBOL(sun4i_frontend_update_buffer);
>
> @@ -130,6 +142,8 @@ static int
> sun4i_frontend_drm_format_to_input_fmt(uint32_t fmt, u32 *val)
> {
> if (!drm_format_is_yuv(fmt))
> *val = SUN4I_FRONTEND_INPUT_FMT_DATA_FMT_RGB;
> + else if (drm_format_is_yuv_sampling_420(fmt))
> + *val = SUN4I_FRONTEND_INPUT_FMT_DATA_FMT_YUV420;
> else if (drm_format_is_yuv_sampling_422(fmt))
> *val = SUN4I_FRONTEND_INPUT_FMT_DATA_FMT_YUV422;
> else
> @@ -140,12 +154,20 @@ static int
> sun4i_frontend_drm_format_to_input_fmt(uint32_t fmt, u32 *val)
>
> static int sun4i_frontend_drm_format_to_input_mode(uint32_t fmt, u32 *val)
> {
> - if (drm_format_num_planes(fmt) == 1)
> + int num_planes = drm_format_num_planes(fmt);
> +
> + switch (num_planes) {
> + case 1:You seem to use either the helper or retrieve the structure field directly to access the number of planes. I'm fine either way, but this should be consistent. Maxime -- Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
signature.asc
Description: PGP signature
_______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
