It is very common for an i2c device to require a small 1 or 2 byte write
followed by a read. For example, when reading from an i2c EEPROM it is
common to write and address, offset or index followed by a reading some
values.
The i915 gmbus controller provides a special "INDEX" cycle for performing
such a small write followed by a read. The INDEX can be either one or two
bytes long. The advantage of using such a cycle is that the CPU has
slightly less work to do once the read with INDEX cycle is started.
Signed-off-by: Daniel Kurtz <djku...@chromium.org>
---
drivers/gpu/drm/i915/intel_i2c.c | 32 ++++++++++++++++++++++++++++++--
1 files changed, 30 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_i2c.c b/drivers/gpu/drm/i915/intel_i2c.c
index 25f2c9e..cb1db10 100644
--- a/drivers/gpu/drm/i915/intel_i2c.c
+++ b/drivers/gpu/drm/i915/intel_i2c.c
@@ -204,13 +204,15 @@ intel_gpio_setup(struct intel_gmbus *bus, u32 pin)
}
static int
-gmbus_xfer_read(struct drm_i915_private *dev_priv, struct i2c_msg *msg)
+gmbus_xfer_read(struct drm_i915_private *dev_priv, struct i2c_msg *msg,
+ u32 gmbus1)
{
int reg_offset = dev_priv->gpio_mmio_base;
u16 len = msg->len;
u8 *buf = msg->buf;
I915_WRITE(GMBUS1 + reg_offset,
+ gmbus1 |
GMBUS_CYCLE_WAIT |
(len << GMBUS_BYTE_COUNT_SHIFT) |
(msg->addr << GMBUS_SLAVE_ADDR_SHIFT) |
@@ -300,8 +302,34 @@ gmbus_xfer(struct i2c_adapter *adapter,
I915_WRITE(GMBUS0 + reg_offset, bus->reg0);
for (i = 0; i < num; i++) {
+ bool last = i + 1 == num;
+ u32 gmbus1 = 0;
+ u32 gmbus5 = 0;
+
+ /*
+ * The gmbus controller can combine a 1 or 2 byte write with a
+ * read that immediately follows it by using an "INDEX" cycle.
+ */
+ if (!last &&
+ !(msgs[i].flags & I2C_M_RD) &&
+ (msgs[i + 1].flags & I2C_M_RD) &&
+ msgs[i].len <= 2) {
+ if (msgs[i].len == 2)
+ gmbus5 = GMBUS_2BYTE_INDEX_EN |
+ msgs[i].buf[1] |
+ (msgs[i].buf[0] << 8);
+ if (msgs[i].len == 1)
+ gmbus1 = GMBUS_CYCLE_INDEX |
+ (msgs[i].buf[0] <<
+ GMBUS_SLAVE_INDEX_SHIFT);
+ i += 1; /* set i to the index of the read xfer */
+ }
+
+ /* GMBUS5 holds 16-bit index, but must be 0 if not used */
+ I915_WRITE(GMBUS5 + reg_offset, gmbus5);
+
if (msgs[i].flags & I2C_M_RD)
- ret = gmbus_xfer_read(dev_priv, &msgs[i]);
+ ret = gmbus_xfer_read(dev_priv, &msgs[i], gmbus1);
else
ret = gmbus_xfer_write(dev_priv, &msgs[i]);
--
1.7.7.3
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/dri-devel
