Hi Russell,
On 08/12/17 12:59, Russell King - ARM Linux wrote:
> On Wed, Dec 06, 2017 at 02:54:04PM +0100, Hans Verkuil wrote:
>> On 12/06/17 13:35, Russell King wrote:
>>> We no longer use the CEC client to access the CEC part itself, so we can
>>> move this later in the initialisation sequence.
>>>
>>> Signed-off-by: Russell King <rmk+ker...@armlinux.org.uk>
>>> ---
>>> drivers/gpu/drm/i2c/tda998x_drv.c | 7 ++++---
>>> 1 file changed, 4 insertions(+), 3 deletions(-)
>>>
>>> diff --git a/drivers/gpu/drm/i2c/tda998x_drv.c
>>> b/drivers/gpu/drm/i2c/tda998x_drv.c
>>> index 7f4dbca7f7f4..4aeac2127974 100644
>>> --- a/drivers/gpu/drm/i2c/tda998x_drv.c
>>> +++ b/drivers/gpu/drm/i2c/tda998x_drv.c
>>> @@ -1490,9 +1490,6 @@ static int tda998x_create(struct i2c_client *client,
>>> struct tda998x_priv *priv)
>>> priv->cec_addr = 0x34 + (client->addr & 0x03);
>>> priv->current_page = 0xff;
>>> priv->hdmi = client;
>>> - priv->cec = i2c_new_dummy(client->adapter, priv->cec_addr);
>>> - if (!priv->cec)
>>> - return -ENODEV;
>>>
>>> /* wake up the device: */
>>> cec_write(priv, REG_CEC_ENAMODS,
>>> @@ -1546,6 +1543,10 @@ static int tda998x_create(struct i2c_client *client,
>>> struct tda998x_priv *priv)
>>> CEC_FRO_IM_CLK_CTRL_GHOST_DIS |
>>> CEC_FRO_IM_CLK_CTRL_IMCLK_SEL);
>>>
>>> /* initialize the optional IRQ */
>>> + priv->cec = i2c_new_dummy(client->adapter, priv->cec_addr);
>>> + if (!priv->cec)
>>> + return -ENODEV;
>>> +
>>
>> I'd move this up to before the 'initialize the optional IRQ' comment, since
>> that should stay with the 'if (client->irq) {' line below.
>
> I've swapped the order of patches 2 and 3, and moved this further down
> near where we add the real cec device in a later patch. This is
> starting to get quite different from the patch series that I've tested,
> and as I've already mentioned, testing is not going to happen for a
> while.
>
I added support for this to am335x-boneblack-common.dtsi (see patch below), but
it doesn't work. I suspect the calibration since I see these messages:
gpio-57 (nxp,calib): gpiod_direction_output: tried to set a GPIO tied to an IRQ
as output
Which makes sense. I had a similar case in my cec-gpio driver and I had to
completely
free the interrupt before I could set the direction to output.
I do get nice interrupts when a transmit is done, so the interrupt works
correctly.
And it correctly detects Ack/Nack.
I looked a bit closer and I see that even without calibration the timings are
reasonably
OK: 2.3 ms for a bit period instead of the recommended 2.4 ms. Slightly off but
within
margins.
But receiving messages fails: I get no interrupt at all. Not sure if the lack of
calibration is the cause of that, or if it is something else. I can take
another look
once the calibration is fixed.
Regards,
Hans
Signed-off-by: Hans Verkuil <hans.verk...@cisco.com>
---
diff --git a/arch/arm/boot/dts/am335x-boneblack-common.dtsi
b/arch/arm/boot/dts/am335x-boneblack-common.dtsi
index 325daae40278..07e6b36d17c4 100644
--- a/arch/arm/boot/dts/am335x-boneblack-common.dtsi
+++ b/arch/arm/boot/dts/am335x-boneblack-common.dtsi
@@ -7,6 +7,7 @@
*/
#include <dt-bindings/display/tda998x.h>
+#include <dt-bindings/interrupt-controller/irq.h>
&ldo3_reg {
regulator-min-microvolt = <1800000>;
@@ -91,6 +92,8 @@
tda19988: tda19988 {
compatible = "nxp,tda998x";
reg = <0x70>;
+ nxp,calib-gpios = <&gpio1 25 0>;
+ interrupts-extended = <&gpio1 25 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default", "off";
pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
