hean.loong....@intel.com writes: > From: "Ong, Hean Loong" <hean.loong....@intel.com> > > Driver for Intel FPGA Video and Image Processing > Suite Frame Buffer II. The driver only supports the Intel > Arria10 devkit and its variants. This driver can be either > loaded staticlly or in modules. The OF device tree binding > is located at: > Documentation/devicetree/bindings/display/altr,vip-fb2.txt > > Signed-off-by: Ong, Hean Loong <hean.loong....@intel.com>
I'm not sure if this driver is going to make sense as-is, if it doesn't actually do display of planes from system memory. But in case I was wrong, here's my review: > diff --git a/drivers/gpu/drm/ivip/intel_vip_conn.c > b/drivers/gpu/drm/ivip/intel_vip_conn.c > new file mode 100644 > index 0000000..499d3b4 > --- /dev/null > +++ b/drivers/gpu/drm/ivip/intel_vip_conn.c > @@ -0,0 +1,96 @@ > +/* > + * intel_vip_conn.c -- Intel Video and Image Processing(VIP) > + * Frame Buffer II driver > + * > + * This driver supports the Intel VIP Frame Reader component. > + * More info on the hardware can be found in the Intel Video > + * and Image Processing Suite User Guide at this address > + * http://www.altera.com/literature/ug/ug_vip.pdf. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms and conditions of the GNU General Public License, > + * version 2, as published by the Free Software Foundation. > + * > + * This program is distributed in the hope it will be useful, but WITHOUT > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for > + * more details. > + * > + * Authors: > + * Ong, Hean-Loong <hean.loong....@intel.com> > + * > + */ > + > +#include <linux/init.h> > +#include <linux/kernel.h> > +#include <drm/drm_atomic_helper.h> > +#include <drm/drm_crtc_helper.h> > +#include <drm/drm_encoder_slave.h> > +#include <drm/drm_plane_helper.h> > + > +static enum drm_connector_status > +intelvipfb_drm_connector_detect(struct drm_connector *connector, bool force) > +{ > + return connector_status_connected; > +} > + > +static void intelvipfb_drm_connector_destroy(struct drm_connector *connector) > +{ > + drm_connector_unregister(connector); > + drm_connector_cleanup(connector); > +} > + > +static const struct drm_connector_funcs intelvipfb_drm_connector_funcs = { > + .dpms = drm_helper_connector_dpms, > + .reset = drm_atomic_helper_connector_reset, > + .detect = intelvipfb_drm_connector_detect, > + .fill_modes = drm_helper_probe_single_connector_modes, > + .destroy = intelvipfb_drm_connector_destroy, > + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, > + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, > +}; > + > +static int intelvipfb_drm_connector_get_modes(struct drm_connector > *connector) > +{ > + struct drm_device *drm = connector->dev; > + int count; > + > + count = drm_add_modes_noedid(connector, drm->mode_config.max_width, > + drm->mode_config.max_height); > + drm_set_preferred_mode(connector, drm->mode_config.max_width, > + drm->mode_config.max_height); > + return count; > +} You're adding a bunch of modes here, but I don't see anywhere in the driver that you change the resolution being scanned out. If you can't change resolution, then I'd probably use drm_gtf_mode() or something to generate just the one mode (do you have a vrefresh for it?). Also, in the simple display pipe's atomic_check, make sure that the mode chosen is the width/height you can support. > + > +static const struct drm_connector_helper_funcs > +intelvipfb_drm_connector_helper_funcs = { > + .get_modes = intelvipfb_drm_connector_get_modes, > +}; > + > +struct drm_connector * > +intelvipfb_conn_setup(struct drm_device *drm) > +{ > + struct drm_connector *conn; > + int ret; > + > + conn = devm_kzalloc(drm->dev, sizeof(*conn), GFP_KERNEL); > + if (IS_ERR(conn)) > + return NULL; > + > + ret = drm_connector_init(drm, conn, &intelvipfb_drm_connector_funcs, > + DRM_MODE_CONNECTOR_DisplayPort); Are you actually outputting DisplayPort (https://en.wikipedia.org/wiki/DisplayPort)? You probably want something else from the DRM_MODE_CONNECTOR list, or maybe just DRM_MODE_CONNECTOR_Unknown. > + if (ret < 0) { > + dev_err(drm->dev, "failed to initialize drm connector\n"); > + ret = -ENOMEM; > + goto error_connector_cleanup; > + } > + > + drm_connector_helper_add(conn, &intelvipfb_drm_connector_helper_funcs); > + > + return conn; > + > +error_connector_cleanup: > + drm_connector_cleanup(conn); > + > + return NULL; > +} > diff --git a/drivers/gpu/drm/ivip/intel_vip_core.c > b/drivers/gpu/drm/ivip/intel_vip_core.c > new file mode 100644 > index 0000000..4e83343 > --- /dev/null > +++ b/drivers/gpu/drm/ivip/intel_vip_core.c > @@ -0,0 +1,171 @@ > +/* > + * intel_vip_core.c -- Intel Video and Image Processing(VIP) > + * Frame Buffer II driver > + * > + * This driver supports the Intel VIP Frame Reader component. > + * More info on the hardware can be found in the Intel Video > + * and Image Processing Suite User Guide at this address > + * http://www.altera.com/literature/ug/ug_vip.pdf. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms and conditions of the GNU General Public License, > + * version 2, as published by the Free Software Foundation. > + * > + * This program is distributed in the hope it will be useful, but WITHOUT > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for > + * more details. > + * > + * Authors: > + * Ong, Hean-Loong <hean.loong....@intel.com> > + * > + */ > + > +#include <linux/init.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > + > +#include <drm/drmP.h> > +#include <drm/drm_atomic.h> > +#include <drm/drm_atomic_helper.h> > +#include <drm/drm_crtc_helper.h> > +#include <drm/drm_fb_helper.h> > +#include <drm/drm_fb_cma_helper.h> > +#include <drm/drm_gem_cma_helper.h> > +#include <drm/drm_plane_helper.h> > +#include <drm/drm_simple_kms_helper.h> > + > +#include "intel_vip_drv.h" > + > +static const u32 fbpriv_formats[] = { > + DRM_FORMAT_XRGB8888, > + DRM_FORMAT_RGB565 > +}; You're registering that you support this set of formats, but I don't see anything programming the hardware differently based on the format of the plane. > +static void intelvipfb_start_hw(void __iomem *base, resource_size_t addr) > +{ > + /* > + * The frameinfo variable has to correspond to the size of the VIP Suite > + * Frame Reader register 7 which will determine the maximum size used > + * in this frameinfo > + */ > + > + u32 frameinfo; > + > + frameinfo = > + readl(base + INTELVIPFB_FRAME_READER) & 0x00ffffff; > + writel(frameinfo, base + INTELVIPFB_FRAME_INFO); > + writel(addr, base + INTELVIPFB_FRAME_START); > + /* Finally set the control register to 1 to start streaming */ > + writel(1, base + INTELVIPFB_CONTROL); > +} The addr you're passing in here is from dev->mode_config.fb_base, which is this weird sideband value from drm_fbdev_cma. It's the wrong value to use if anything else uses the KMS interfaces to change the plane -- you should be using drm_fb_cma_get_gem_addr(drm_simple_display_pipe->plane->state, 0) instead. > + > +static void intelvipfb_disable_hw(void __iomem *base) > +{ > + /* set the control register to 0 to stop streaming */ > + writel(0, base + INTELVIPFB_CONTROL); > +} These two functions should be be called from fbpriv_funcs.enable() and .disable(), not device load/unload. > +static const struct drm_mode_config_funcs intelvipfb_mode_config_funcs = { > + .fb_create = drm_fb_cma_create, > + .atomic_check = drm_atomic_helper_check, > + .atomic_commit = drm_atomic_helper_commit, > +}; > + > +static struct drm_mode_config_helper_funcs intelvipfb_mode_config_helpers = { > + .atomic_commit_tail = drm_atomic_helper_commit_tail, > +}; > + > +static void intelvipfb_setup_mode_config(struct drm_device *drm) > +{ > + drm_mode_config_init(drm); > + drm->mode_config.funcs = &intelvipfb_mode_config_funcs; > + drm->mode_config.helper_private = &intelvipfb_mode_config_helpers; > +} > + > +static int intelvipfb_pipe_prepare_fb(struct drm_simple_display_pipe *pipe, > + struct drm_plane_state *plane_state) > +{ > + return drm_fb_cma_prepare_fb(&pipe->plane, plane_state); > +} > + > +static struct drm_simple_display_pipe_funcs fbpriv_funcs = { > + .prepare_fb = intelvipfb_pipe_prepare_fb, > +}; > + > +int intelvipfb_probe(struct device *dev, void __iomem *base) > +{ > + int retval; > + struct drm_device *drm; > + struct intelvipfb_priv *fbpriv = dev_get_drvdata(dev); > + struct drm_connector *connector; > + > + dev_set_drvdata(dev, fbpriv); > + > + drm = fbpriv->drm; > + > + intelvipfb_setup_mode_config(drm); > + > + connector = intelvipfb_conn_setup(drm); > + if (!connector) { > + dev_err(drm->dev, "Connector setup failed\n"); > + goto err_mode_config; > + } > + > + retval = drm_simple_display_pipe_init(drm, &fbpriv->pipe, > + &fbpriv_funcs, > + fbpriv_formats, > + ARRAY_SIZE(fbpriv_formats), > + connector); > + if (retval < 0) { > + dev_err(drm->dev, "Cannot setup simple display pipe\n"); > + goto err_mode_config; > + } > + > + fbpriv->fbcma = drm_fbdev_cma_init(drm, PREF_BPP, > + drm->mode_config.num_connector); > + if (!fbpriv->fbcma) { > + fbpriv->fbcma = NULL; > + dev_err(drm->dev, "Failed to init FB CMA area\n"); > + goto err_mode_config; > + } On failure, drm_fbdev_cma_init() returns an ERR_PTR, not NULL. Also, you're passing this PREF_BPP value here, ignoring the altr,bits-per-symbol property. That seems wrong.
signature.asc
Description: PGP signature
_______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
