On Mon, Jan 30, 2017 at 06:14:27PM +0000, John Keeping wrote:
> On Mon, 30 Jan 2017 10:26:11 -0500, Sean Paul wrote:
>
> > On Sun, Jan 29, 2017 at 01:24:44PM +0000, John Keeping wrote:
> > > I haven't found any method for getting the length of a response, so this
> > > just uses the requested rx_len
> > >
> > > Signed-off-by: John Keeping <j...@metanate.com>
> > > ---
> > > v3:
> > > - Fix checkpatch warnings
> > > Unchanged in v2
> > >
> > > drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 56
> > > ++++++++++++++++++++++++++++++++++
> > > 1 file changed, 56 insertions(+)
> > >
> > > diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> > > b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> > > index cf3ca6b0cbdb..cc58ada75425 100644
> > > --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> > > +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> > > @@ -678,6 +678,56 @@ static int dw_mipi_dsi_dcs_long_write(struct
> > > dw_mipi_dsi *dsi,
> > > return dw_mipi_dsi_gen_pkt_hdr_write(dsi, hdr_val);
> > > }
> > >
> > > +static int dw_mipi_dsi_dcs_read(struct dw_mipi_dsi *dsi,
> > > + const struct mipi_dsi_msg *msg)
> > > +{
> > > + const u8 *tx_buf = msg->tx_buf;
> > > + u8 *rx_buf = msg->rx_buf;
> > > + size_t i;
> > > + int ret, val;
> > > +
> > > + dsi_write(dsi, DSI_PCKHDL_CFG, EN_CRC_RX | EN_ECC_RX | EN_BTA);
> > > + dsi_write(dsi, DSI_GEN_HDR,
> > > + GEN_HDATA(tx_buf[0]) | GEN_HTYPE(msg->type));
> > > +
> > > + ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
> > > + val, !(val & GEN_RD_CMD_BUSY), 1000,
> > > + CMD_PKT_STATUS_TIMEOUT_US);
> > > + if (ret < 0) {
> > > + dev_err(dsi->dev, "failed to read command response\n");
> > > + return ret;
> > > + }
> > > +
> > > + for (i = 0; i < msg->rx_len;) {
> > > + u32 pld = dsi_read(dsi, DSI_GEN_PLD_DATA);
> > > +
> > > + while (i < msg->rx_len) {
> > > + rx_buf[i] = pld & 0xff;
> > > + pld >>= 8;
> > > + i++;
> > > + }
> > > + }
> >
> > AFAICT, the outer for loop just initializes i and ensures msg->rx_len is
> > non-zero?
> >
> > I think the following would be easier to read (and safe against the case
> > where
> > msg->rx_len > sizeof(pld) (even though this shouldn't happen according to
> > DCS
> > spec)).
> >
> > if (msg->rx_len > 0) {
> > u32 pld = dsi_read(dsi, DSI_GEN_PLD_DATA);
> > memcpy(rx_buf, &pld, MIN(msg->rx_len, sizeof(pld));
> > }
>
> I think the intent was to handle rx_len > 4, but the patch is obvously
> completely broken regarding that. As far as I can tell, rx_len is
> limited by the maximum return packet size which can be any value up to
> the maximum size of a long packet, so we may need to read from the FIFO
> multiple times.
>
> The loop should be something like this:
>
> for (i = 0; i < msg->rx_len;) {
> u32 pld = dsi_read(dsi, DSI_GEN_PLD_DATA);
> int j;
>
> for (j = 0; j < 4 && i < msg->rx_len; i++, j++) {
> rx_buf[i] = pld & 0xff;
> pld >>= 8;
> }
> }
Short packets should never exceed 32 bits, so I don't think you need to add the
nested loop.
Sean
>
> I have successfully read 5 bytes from a DSI display using this code, but
> I'm tempted to just drop this patch since I only used it for debugging
> while bringing up a new panel.
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
--
Sean Paul, Software Engineer, Google / Chromium OS
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
