Hi Thierry
When I'm preparing v3 series, I meet some trobules from your comment,
wish you could give some advise? ;)
å¨ 2015/8/10 18:00, Thierry Reding åé:
> On Sat, Aug 08, 2015 at 11:54:38AM +0800, Yakir Yang wrote:
> [...]
>> edp: edp at ff970000 {
> [...]
>> samsung,color-space = <0>;
>> samsung,dynamic-range = <0>;
>> samsung,ycbcr-coeff = <0>;
> I think these should also come from EDID, though I'm not sure if we
> store this in internal data structures yet.
>
>> samsung,color-depth = <1>;
> This is probably drm_display_info.bpc.
"samsung,color_space" and "samsung,color-depth"
The drm_display_info's color_formats and bpc indicate the monitor
display ability, but
the edp driver could not take it as input video format directly.
For example, with my DP TV I would found "RGB444 & YCRCB422 & & YCRCB444"
support in drm_display_info.color_formats and 16bit bpc support, but
RK3288 crtc
driver could only output RGB & ITU formats, so finally
analogix_dp-rockchip driver
config crtc to RGBaaa 10bpc mode.
In this sutiation, the analogix_dp core driver would pazzled by the
drm_display_info,
can't chose the right color_space and bpc.
And this is the place that confused me, wish you could give some ideas
about this one :-)
-------------------------------------------------------------------------------------------------
Besides, The dynamic_range and ycbcr_coeff haven't been record in
drm_display_info, but
I though we can parse it by the video code.
The dynamic_range would have two values "CEA range" and "VESA range", so
I though if
the currect mode have a no-zero vic (drm_match_cea_mode()) then config
it to "CEA range",
otherwhise config it to "VESA range".
YCbCr Coefficients would have two values "ITU709" and "ITU601". I see
dw_hdmi driver have
been set the colorimetry to ITU_601 when vic is 6/7/21/22/2/3/17/18, I
thouht we can stole this
to analogix_dp driver.
/* dynamic_range & colorimetry */
vic = drm_match_cea_mode(mode);
if ((vic == 6) || (vic == 7) || (vic == 21) || (vic == 22) ||
(vic == 2) || (vic == 3) || (vic == 17) || (vic == 18)) {
video_info->dynamic_range = CEA;
video_info->ycbcr_coeff = COLOR_YCBCR601;
} else if (vic) {
video_info->dynamic_range = CEA;
video_info->ycbcr_coeff = COLOR_YCBCR709;
} else {
video_info->dynamic_range = VESA;
video_info->ycbcr_coeff = COLOR_YCBCR709;
}
I'm not sure whether this is right, also wish you could give some
suggests ;)
>> samsung,link-rate = <0x0a>;
>> samsung,lane-count = <1>;
> And these should really be derived from values in the DPCD and adjusted
> (if necessary) during link training.
>
> Why would you ever want to hard-code the above?
>
And I though we should keep those DT properties now. I try to remove
those DT
property, so analogix dp driver would always use the max link_rate and
lane_count
which read from dpcd. For my 2K DP TV, link rate would reach to 5.4Gbps,
lane cout
would reach 4 lances, if so analogix dp driver could not light my DP TV
up any more.
After that I found that RK3288 eDP TRM have indicated some limites about
those
that RK3288 only support 4 physical lanes of 2.7/1.62 Gbps/lane, which
means 5.4Gbps
link rate is too high for RK3288.
So I think we could treate them as hardware max values, is it okay?
Thanks,
- Yakir
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://lists.freedesktop.org/archives/dri-devel/attachments/20150819/29017b21/attachment-0001.html>
