Hi, I've been asked to try and get a r600 based (E6460) graphics card running on a machine powered by a Freescale p4080 (e500 core). I've run into a bit of a problem.
I have the driver built into the kernel at this point. When I boot the card is detected and it seems to be finding the fimware (I'm also building in the required firmware blobs), but I get the following messages: [drm] Initialized drm 1.1.0 20060810 [drm] radeon defaulting to kernel modesetting. [drm] radeon kernel modesetting enabled. [drm] initializing kernel modesetting (CAICOS 0x1002:0x6763 0x1775:0xC6A7). [drm] register mmio base: 0x10000000 [drm] register mmio size: 131072 ATOM BIOS: GE [drm] GPU not posted. posting now... radeon 0000:04:00.0: VRAM: 512M 0x0000000000000000 - 0x000000001FFFFFFF (512M used) radeon 0000:04:00.0: GTT: 512M 0x0000000020000000 - 0x000000003FFFFFFF [drm] Detected VRAM RAM=512M, BAR=256M [drm] RAM width 64bits DDR [TTM] Zone kernel: Available graphics memory: 338754 kiB [TTM] Zone highmem: Available graphics memory: 994110 kiB [TTM] Initializing pool allocator [TTM] Initializing DMA pool allocator [drm] radeon: 512M of VRAM memory ready [drm] radeon: 512M of GTT memory ready. [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [drm] Driver supports precise vblank timestamp query. radeon 0000:04:00.0: radeon: using MSI. [drm] radeon: irq initialized. [drm] GART: num cpu pages 131072, num gpu pages 131072 [drm] probing gen 2 caps for device 111d:808a = 2/0 [drm] enabling PCIE gen 2 link speeds, disable with radeon.pcie_gen2=0 [drm] Loading CAICOS Microcode __ioremap_caller(140000, 4096, 4194304, c02eab20)__ioremap(): phys addr 0x140000 is RAM lr ttm_bo_kmap radeon 0000:04:00.0: disabling GPU acceleration radeon 0000:04:00.0: e957e400 unpin not necessary radeon 0000:04:00.0: e957e400 unpin not necessary [drm] Radeon Display Connectors [drm] Connector 0: [drm] DP-1 [drm] HPD2 [drm] HPD3 [drm] DDC: 0x6450 0x6450 0x6454 0x6454 0x6458 0x6458 0x645c 0x645c [drm] Encoders: [drm] DFP2: INTERNAL_UNIPHY1 [drm] Connector 2: [drm] DVI-I-1 [drm] HPD1 [drm] DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438 0x643c 0x643c [drm] Encoders: [drm] DFP3: INTERNAL_UNIPHY [drm] CRT1: INTERNAL_KLDSCP_DAC1 [drm] Internal thermal controller with fan control [drm] radeon: power management initialized __ioremap_caller(141000, 5242880, 4194304, c02eab20)__ioremap(): phys addr 0x141000 is RAM lr ttm_bo_kmap [drm:radeonfb_create] *ERROR* failed to create fbcon object -12 [drm] Initialized radeon 2.29.0 20080528 for 0000:04:00.0 on minor 0 There are failed attempts to ioremap RAM, initially as part of r600_vram_scratch_init() and again I guess mapping the GART? On the e500, overlapping TLBs are not allowed and there is an explict check in arch/powerpc/mm/pgtable_32.c __ioremap_caller() to protect against ioremapping RAM that's already got TLB entries which is resulting in the error messages. I'm out of ideas, any pointers or suggestions on how I might get this working? Has this ever been attempted before? Martyn -- Martyn Welch (Lead Software Engineer) | Registered in England and Wales GE Intelligent Platforms | (3828642) at 100 Barbirolli Square T +44(0)1327322748 | Manchester, M2 3AB E martyn.welch at ge.com | VAT:GB 927559189
