Am 2020-06-15 05:11, schrieb spiralofhope:
I wonder if there's anything S.M.A.R.T. information can tell you.
There is a spinup time test, and I wonder if perhaps there is SMART
logging within the drive that could reveal a problem with the drive not
spinning up as quickly as it should, and maybe that is causing a
problem (somehow).
=== START OF INFORMATION SECTION ===
Model Family: WDC HGST Ultrastar He10
Device Model: WDC WD100EMAZ-00WJTA0
Serial Number: 1EGNK46Z
LU WWN Device Id: 5 000cca 27ec957bf
Firmware Version: 83.H0A83
User Capacity: 10.000.831.348.736 bytes [10,0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Jun 15 06:23:41 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 93) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon
new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test
supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging
supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: (1159) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control
supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always
- 0
2 Throughput_Performance 0x0004 130 130 054 Old_age
Offline - 110
3 Spin_Up_Time 0x0007 194 194 024 Pre-fail Always
- 328 (Average 350)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always
- 394
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000a 100 100 067 Old_age Always
- 0
8 Seek_Time_Performance 0x0004 128 128 020 Old_age
Offline - 18
9 Power_On_Hours 0x0012 100 100 000 Old_age Always
- 4610
10 Spin_Retry_Count 0x0012 100 100 060 Old_age Always
- 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always
- 393
22 Helium_Level 0x0023 100 100 025 Pre-fail Always
- 100
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 561
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always
- 561
194 Temperature_Celsius 0x0002 180 180 000 Old_age Always
- 36 (Min/Max 12/48)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always
- 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute
delay.
This may sound dumb, but does the drive _sound_ different when first
powered with the system, and does the sound change when it is mounted?
Does it sound like it's "waking up" only when you manually mount it?
No, the sound does not change when mounted. The only noise is head
movement on access.
_______________________________________________
Dng mailing list
Dng@lists.dyne.org
https://mailinglists.dyne.org/cgi-bin/mailman/listinfo/dng
