oh.. I think now I know what you are trying to explain to me. Thank you so much It helped me a lot.
But I still have problem. I am sending udp packet. It means that destination macaddress is the only factor that influence the selection. Also, I missed one more thing. I had more buckets updated. 2016-08-02 14:39 GMT+09:00 Ben Pfaff <b...@ovn.org>: > No, hashes are stateless. They don't get erased. > > On Tue, Aug 02, 2016 at 02:25:44PM +0900, 허지민 wrote: > > Well, I am sure about it. > > Destination or source did not change. > > > > There is nothing like timeout??? > > > > I thought that after a long term without any networking, all the hashed > > data would be erased. > > > > > > 2016-08-02 14:11 GMT+09:00 Ben Pfaff <b...@ovn.org>: > > > > > Probably your new flows have different source or destination TCP ports. > > > > > > On Tue, Aug 02, 2016 at 01:57:08PM +0900, 허지민 wrote: > > > > I'am using 2.5.0 > > > > > > > > 2016-08-02 13:08 GMT+09:00 Ben Pfaff <b...@ovn.org>: > > > > > > > > > What version of Open vSwitch are you using? > > > > > > > > > > On Tue, Aug 02, 2016 at 11:29:22AM +0900, 허지민 wrote: > > > > > > Thank you for answering. > > > > > > > > > > > > I'm not sure if I understood right. > > > > > > > > > > > > The answer is saying that, if I don't change source or > destination, > > > > > bucket > > > > > > selection won't be redone? > > > > > > > > > > > > Well, I am using group table for my project, and each bucket in > the > > > group > > > > > > has > > > > > > different weight. When I tested group table, I found out that > after > > > long > > > > > > term without networking, the selection has changed and send > packets > > > to > > > > > > different bucket. > > > > > > > > > > > > How does weight of the bucket influence the selection??? > > > > > > > > > > > > 2016-08-02 2:10 GMT+09:00 Ben Pfaff <b...@ovn.org>: > > > > > > > > > > > > > On Mon, Aug 01, 2016 at 05:39:10PM +0900, 허지민 wrote: > > > > > > > > I am working on a project using group table select. > > > > > > > > > > > > > > > > I am figuring out how group table select one of the buckets > that > > > is > > > > > added > > > > > > > > in the group. > > > > > > > > > > > > > > This is in the FAQ. > > > > > > > > > > > > > > ### Q: How does OVS divide flows among buckets in an OpenFlow > > > "select" > > > > > > > group? > > > > > > > > > > > > > > A: In Open vSwitch 2.3 and earlier, Open vSwitch used the > > > destination > > > > > > > Ethernet address to choose a bucket in a select group. > > > > > > > > > > > > > > Open vSwitch 2.4 and later by default hashes the source and > > > > > > > destination Ethernet address, VLAN ID, Ethernet type, > IPv4/v6 > > > > > > > source and destination address and protocol, and for TCP and > > > SCTP > > > > > > > only, the source and destination ports. The hash is > > > "symmetric", > > > > > > > meaning that exchanging source and destination addresses > does > > > not > > > > > > > change the bucket selection. > > > > > > > > > > > > > > Select groups in Open vSwitch 2.4 and later can be > configured to > > > > > > > use a different hash function, using a Netronome extension > to > > > the > > > > > > > OpenFlow 1.5+ group_mod message. For more information, see > > > > > > > Documentation/group-selection-method-property.txt in the > Open > > > > > > > vSwitch source tree. (OpenFlow 1.5 support in Open vSwitch > is > > > still > > > > > > > experimental.) > > > > > > > > > > > > > > > >
_______________________________________________ discuss mailing list discuss@openvswitch.org http://openvswitch.org/mailman/listinfo/discuss
