The log messages are as clear I can make them. You need to configure a certificate and a private key. However you are doing it, you are doing it wrong. The Open vSwitch automatic tests manage to do this just fine whenever someone runs "make check" so I know that it works.
On Wed, Nov 20, 2013 at 02:24:19PM +0530, sonia verma wrote: > Hi Ben > > I have performed all the configuration described in OVS.Is there anything > else which I need to configure? > I'm using OVS versioon 1-11 for this. > > > > On Wed, Nov 20, 2013 at 12:21 PM, Ben Pfaff <b...@nicira.com> wrote: > > > It looks like you didn't configure a private key and a certificate. > > > > On Wed, Nov 20, 2013 at 12:15:46PM +0530, abhishek jain wrote: > > > Hi Ben > > > > > > I have followed the same process as described in INSTALL.SSL but still > > the > > > result is same. > > > Can you help regarding this? > > > > > > > > > > > > On Wed, Nov 20, 2013 at 11:19 AM, Ben Pfaff <b...@nicira.com> wrote: > > > > > > > On Wed, Nov 20, 2013 at 11:08:34AM +0530, abhishek jain wrote: > > > > > Thanks for your help. > > > > > I'm getting following error when configuring OVS for ssl. > > > > > > > > > > stream_ssl|ERR|Certificate must be configured to use SSL > > > > > 2013-11-20T05:29:49Z|00598|rconn|WARN|br0<->ssl:192.168.6.129:6633: > > > > > connection failed (Protocol not available) > > > > > 2013-11-20T05:29:57Z|00599|stream_ssl|ERR|Private key must be > > configured > > > > to > > > > > use SSL > > > > > 2013-11-20T05:29:57Z|00600|stream_ssl|ERR|Certificate must be > > configured > > > > to > > > > > use SSL > > > > > 2013-11-20T05:29:57Z|00601|rconn|WARN|br0<->ssl:192.168.6.129:6633: > > > > > connection failed (Protocol not available) > > > > > 2013-11-20T05:30:05Z|00602|stream_ssl|ERR|Private key must be > > configured > > > > to > > > > > use SSL > > > > > 2013-11-20T05:30:05Z|00603|stream_ssl|ERR|Certificate must be > > configured > > > > to > > > > > use SSL > > > > > 2013-11-20T05:30:05Z|00604|rconn|WARN|br0<->ssl:192.168.6.129:6633: > > > > > connection failed (Protocol not available) > > > > > 2013-11-20T05:30:13Z|00605|stream_ssl|ERR|Private key must be > > configured > > > > to > > > > > use SSL > > > > > 2013-11-20T05:30:13Z|00606|stream_ssl|ERR|Certificate must be > > configured > > > > to > > > > > use SSL > > > > > 2013-11-20T05:30:13Z|00607|rconn|WARN|br0<->ssl:192.168.6.129:6633: > > > > > connection failed (Protocol not available) > > > > > 2013-11-20T05:30:21Z|00608|stream_ssl|ERR|Private key must be > > configured > > > > to > > > > > use SSL > > > > > 2013-11-20T05:30:21Z|00609|stream_ssl|ERR|Certificate must be > > configured > > > > to > > > > > use SSL > > > > > 2013-11-20T05:30:21Z|00610|rconn|WARN|br0<->ssl:192.168.6.129:6633: > > > > > connection failed (Protocol not available) > > > > > 2013-11-20T05:30:21Z|00611|fail_open|INFO|Still in fail-open mode > > after > > > > > 1479 seconds disconnected from controller > > > > > > > > > > Do you know how to deal with that. > > > > > > > > I would start by reading INSTALL.SSL. > > > > > > _______________________________________________ > > discuss mailing list > > discuss@openvswitch.org > > http://openvswitch.org/mailman/listinfo/discuss > > _______________________________________________ discuss mailing list discuss@openvswitch.org http://openvswitch.org/mailman/listinfo/discuss
