On Wed, Jan 9, 2013 at 1:30 AM, Mathumitha S <cerisierfi...@hotmail.com> wrote: > Hi, > I have OpenvSwitch installed in a computer that > has a quad port. eth3, eth4 and eth5 are connected to br0 with respective > open flow port numbers as 3,2,1 and the respective IP addresses of the > machines connected to the ports are 10.6.3.2, 10.6.1.2 and 10.6.2.2 > > I use eth3 and eth4 i.e ports 2 and 3 as input port and eth5 (port 1) as > output port of OvS. I created 2 queues at eth5 using the following command: > > ovs-vsctl -- set port eth5 qos=@newqos -- --id=@newqos create qos > type=linux-htb other-config:max-rate=100000000 queues=0=@q0,1=@q1 -- > --id=@q0 create queue other-config:min-rate=20000000 > other-config:max-rate=100000000 -- --id=@q1 create queue > other-config:min-rate=1000000 other-config:max-rate=100000000 > > I then added the following flows in the flow table: > > ovs-ofctl add-flow br0 > "in_port=2,dl_type=0x0800,nw_proto=6,nw_src=10.6.1.2,nw_dst=10.6.2.2,tp_dst=6000,priority=7,actions=enqueue:1:0" > ovs-ofctl add-flow br0 > "in_port=3,dl_type=0x0800,nw_proto=6,nw_src=10.6.3.2,nw_dst=10.6.2.2,tp_dst=6005,priority=7,actions=enqueue:1:1" > ovs-ofctl add-flow br0 > "in_port=1,dl_type=0x0800,nw_proto=6,nw_dst=10.6.1.2,nw_src=10.6.2.2,tp_src=6000,priority=5,actions=output:2" > ovs-ofctl add-flow br0 > "in_port=1,dl_type=0x0800,nw_proto=6,nw_dst=10.6.3.2,nw_src=10.6.2.2,tp_src=6005,priority=5,actions=output:3" > ovs-ofctl add-flow br0 > "in_port=2,dl_type=0x0800,nw_src=10.6.1.2,priority=0,actions=output:1" > ovs-ofctl add-flow br0 > "in_port=3,dl_type=0x0800,,nw_src=10.6.3.2,priority=0,actions=output:1" > > I use iperf to generate traffic from two machines connected to eth3 and > eth4. I use iperf server in machine connected to eth5 at port 6000 for > machine connected to eth4 and at port 6005 for machine connected to eth3. > Hence, basically I am trying ti distinguish flows based on IP address and > destination port number. > > But when I try to generate traffic and test the scenario, I get 'No route to > host' error. > > I basically need to enqueue different flows from different input ports in > different queues at output port. So I only need routes for the TCP packets, > ACK and ARP requests, right? I think I have included these in the rules I > gave above. Can you please tell me what I am missing? Where am I going > wrong? Earlier, I was able to distinguish flows based on iperf port numbers > when I used two iperf clients on the same machine i.e when I had just one > input port and one output port.
There are still no ARP rules. ARP does not have an IP EtherType. _______________________________________________ discuss mailing list discuss@openvswitch.org http://openvswitch.org/mailman/listinfo/discuss
