On 28/12/2022 23:55, Ali G. Dezfuli wrote:
seems it's ok:
$ uhd_usrp_probe
[INFO] [UHD] linux; GNU C++ version 11.3.0; Boost_107400;
UHD_4.3.0.0-14-g1e718d9b
[INFO] [USRP2] Opening a USRP2/N-Series device...
[INFO] [USRP2] Current recv frame size: 1472 bytes
[INFO] [USRP2] Current send frame size: 1472 bytes
_____________________________________________________
/
| Device: USRP2 / N-Series Device
| _____________________________________________________
| /
| | Mboard: N200r4
| | hardware: 2576
| | mac-addr: 00:80:2f:0a:ce:45
| | ip-addr: 192.168.20.2
| | subnet: 255.255.255.255
| | gateway: 255.255.255.255
| | gpsdo: none
| | serial: F1700B
| | name: ali_01
| | FW Version: 12.4
| | FPGA Version: 11.1
| |
| | Time sources: none, external, _external_, mimo
| | Clock sources: internal, external, mimo
| | Sensors: mimo_locked, ref_locked
| | _____________________________________________________
| | /
| | | RX DSP: 0
| | |
| | | Freq range: -50.000 to 50.000 MHz
| | _____________________________________________________
| | /
| | | RX DSP: 1
| | |
| | | Freq range: -50.000 to 50.000 MHz
| | _____________________________________________________
| | /
| | | RX Dboard: A
| | | ID: WBX v3, WBX v3 + Simple GDB (0x0057)
| | | Serial: EDR29PFXW
| | | _____________________________________________________
| | | /
| | | | RX Frontend: 0
| | | | Name: WBXv3 RX+GDB
| | | | Antennas: TX/RX, RX2, CAL
| | | | Sensors: lo_locked
| | | | Freq range: 68.750 to 2200.000 MHz
| | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
| | | | Bandwidth range: 40000000.0 to 40000000.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | RX Codec: A
| | | | Name: ads62p44
| | | | Gain range digital: 0.0 to 6.0 step 0.5 dB
| | | | Gain range fine: 0.0 to 0.5 step 0.1 dB
| | _____________________________________________________
| | /
| | | TX DSP: 0
| | |
| | | Freq range: -200.000 to 200.000 MHz
| | _____________________________________________________
| | /
| | | TX Dboard: A
| | | ID: WBX v3 (0x0056)
| | | Serial: EDR29PFXW
| | | ID: WBX + Simple GDB, WBX v3 + Simple GDB, WBX v4 + Simple
GDB, WBX-120 + Simple GDB (0x004f)
| | | Serial: EDR29PFGS
| | | _____________________________________________________
| | | /
| | | | TX Frontend: 0
| | | | Name: WBXv3 TX+GDB
| | | | Antennas: TX/RX, CAL
| | | | Sensors: lo_locked
| | | | Freq range: 68.750 to 2200.000 MHz
| | | | Gain range PGA0: 0.0 to 31.0 step 1.0 dB
| | | | Bandwidth range: 40000000.0 to 40000000.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | TX Codec: A
| | | | Name: ad9777
| | | | Gain Elements: None
You might try backing-out to UHD 4.2 or even UHD 4.1.0.5 (which is what
is packaged with Ubuntu 22.04).
I recall (haven't found the thread on usrp-users yet) that there was a
problem with the _cal utilities in UHD 4.3.
I'd recommend that you join the usrp-users mailng list, where more
USRP-specific discussions take place.
