Yep, gr-air-modes hasn't been built, installed, or tested by me. Needs the usual rebuild-from-gr-modtool, and I haven't gotten around to it.
Nick On Mon, Oct 3, 2022 at 11:52 AM Philip Balister <phi...@balister.org> wrote: > On 10/3/22 09:34, Michelle wrote: > > Hi Cinaed, > > > > thank you for your answer, It seems like modes_rx (gr3.9 branch) under > > GNU Radio 3.10 hangs somewhere on startup. @willcode4 will try to debug > > it. > > https://github.com/bkerler/gnuradio_install/blob/main/install.sh#L275 > > Suggests this is not fully ported to 3.10 yet. > > Philip > > > > > > have a good day. > > > > On 2022-10-02 19:52, Cinaed Simson wrote: > >> Hi Michelle - the source code version of gr-air-modes from github > >> > >> https://github.com/bistromath/gr-air-modes.git > >> > >> indicates it should build under 3.9 but it doesn't build 3.10 - it > >> can't find > >> > >> GrSwig > >> > >> which is no longer supported. > >> > >> Sometimes OOT modules which work on 3.9 work on 3.10 - sometimes they > >> don't. > >> > >> It's possible your version gr-air-modes has a different author from > >> git hub version above. > >> > >> And I don't have a version of 3.9 either so I can't test it on 3.9 . > >> > >> -- Cinaed > >> > >> > >> > >> On 10/1/22 05:18, Michelle wrote: > >>> Hello, > >>> > >>> I have gnuradio 3.10 and I wanted to install gr-air-modes. In the > >>> chat one of the moderators told me the version of gr-air-modes that > >>> is compatible with gr3.9 would work with gr3.10. > >>> So I installed this version in my computer, the installation was > >>> successfull however when I execute rx_modes I do not receive any > >>> signal. The output of the command is : > >>> > >>> Inspiron-3793:~$ modes_rx > >>> gr-air-modes warning: numpy+scipy not installed, FlightGear interface > >>> not supported > >>> [INFO] [UHD] linux; GNU C++ version 9.2.1 20200304; Boost_107100; > >>> UHD_3.15.0.0-2build5 > >>> [INFO] [B200] Loading firmware image: > >>> /usr/share/uhd/images/usrp_b200_fw.hex... > >>> [INFO] [B200] Detected Device: B200 > >>> [INFO] [B200] Loading FPGA image: > >>> /usr/share/uhd/images/usrp_b200_fpga.bin... > >>> [INFO] [B200] Operating over USB 2. > >>> [INFO] [B200] Detecting internal GPSDO.... > >>> [INFO] [GPS] No GPSDO found > >>> [INFO] [B200] Initialize CODEC control... > >>> [INFO] [B200] Initialize Radio control... > >>> [INFO] [B200] Performing register loopback test... > >>> [INFO] [B200] Register loopback test passed > >>> [INFO] [B200] Setting master clock rate selection to 'automatic'. > >>> [INFO] [B200] Asking for clock rate 16.000000 MHz... > >>> [INFO] [B200] Actually got clock rate 16.000000 MHz. > >>> [INFO] [B200] Asking for clock rate 32.000000 MHz... > >>> [INFO] [B200] Actually got clock rate 32.000000 MHz. > >>> Setting gain to 38 > >>> Gain is 38 > >>> Rate is 4000000 > >>> > >>> please can i get some support to solve this problem? > >>> > >>> > >> > >> > > > >
