FYI all gr-fhss_utils tests pass on a properly configured machine. I highly recommend you use `pybombs` in the future.
Is it possible you have the `maint-3.7` branch of fhss_utils? I think the master branch is for 3.8. Kyle ________________________________ From: Cinaed Simson <cinaed.sim...@gmail.com> Sent: Wednesday, December 2, 2020 13:32 To: Kyle A Logue <kyle.a.lo...@aero.org>; discuss-gnuradio@gnu.org <discuss-gnuradio@gnu.org> Subject: Re: how to auto detect peak frequency in QT FFT sink I was just curious - and the only reason I choose FFT peak was because you did. I built gnuradio and the OOT modules from source. And it doesn't matter where you hang the gnuradio root. And it's highly unlikely that I could compile, link to gnuradio, and run make test with missing dependencies. On the machine I first tested it which was an old 64 bit Dell Optiplex desktop running Debian 10 (buster), and it logs the following error in dmesg: [1233081.177466] traps: python3[22326] trap invalid opcode ip:7feef013fc5c sp:7ffed724b720 error:0 in libgnuradio-fhss_utils.so.42c85270[7feef0133000+1d000] - where I believe error:0 implies division by zero. Then I installed it on a new i5 laptop and it passes the first test - which I presume is the division by 0 error above - but fails the other 2 tests - and doesn't log any errors in dmesg. Then I downloaded and installed gr-pdu_utils and gr-sandia_utils and both of those packages are riddled with make test errors. I'm presuming these are work in progress - and I don't the time right now to explore those errors further. -- Cinaed On 12/1/20 2:17 PM, Kyle A Logue wrote: this might depend on how you install it I see you are using and /opt/ prefix. I just install it with `pybombs install gr-fhss_utils` and it works. Maybe you are missing a dependency? FYI the FFT peak block you want is a simple hier block you could make without installing anything. Look at this file<https://github.com/sandialabs/gr-fhss_utils/blob/maint-3.8/python/fft_peak.py>. Kyle ________________________________ From: Discuss-gnuradio <discuss-gnuradio-bounces+kyle.a.logue=aero....@gnu.org><mailto:discuss-gnuradio-bounces+kyle.a.logue=aero....@gnu.org> on behalf of Cinaed Simson <cinaed.sim...@gmail.com><mailto:cinaed.sim...@gmail.com> Sent: Tuesday, December 1, 2020 13:31 To: discuss-gnuradio@gnu.org<mailto:discuss-gnuradio@gnu.org> <discuss-gnuradio@gnu.org><mailto:discuss-gnuradio@gnu.org> Subject: Re: how to auto detect peak frequency in QT FFT sink Hi Kyle - after I build gr-fhss_utils and run the tests, all 3 tests fail. Do the tests work? I did a pull but it was up to date. I'm running gnuradio 3.8.2.0 on Debian 10 or buster. -- Cinaed Running tests... Test project /opt/gnuradio/src/gr-oot/gr-fhss_utils/build Start 1: qa_cf_estimate 1/3 Test #1: qa_cf_estimate ...................***Failed 0.34 sec Start 2: qa_fft_burst_tagger 2/3 Test #2: qa_fft_burst_tagger ..............***Failed 0.32 sec Start 3: qa_tagged_burst_to_pdu 3/3 Test #3: qa_tagged_burst_to_pdu ...........***Failed 0.32 sec 0% tests passed, 3 tests failed out of 3 Total Test time (real) = 0.99 sec The following tests FAILED: 1 - qa_cf_estimate (Failed) 2 - qa_fft_burst_tagger (Failed) 3 - qa_tagged_burst_to_pdu (Failed) Errors while running CTest make: *** [Makefile:86: test] Error 8 On 12/1/20 8:48 AM, Kyle A Logue wrote:
