2017-05-26 7:27 GMT-05:00 Bastian Bloessl <m...@bastibl.net>: > Hi, > > On 5/26/2017 10:57 AM, Marcus Müller wrote: > >> Hi Cristian, >> >> assuming this is a network config issue >> > > > Me too. I think that trying to ping a local address and having it routed > over interfaces might, in theory, be possible, but hard to setup. > > Try communicating with a WiFi card of another PC. Set the interface to ad > hoc mode and setup static routing and ARP entries. That's what I did in the > video. You already have the script for the SDR host. The other hosts uses > similar IP and ARP configurations (but, of course, doesn't create the > TUN/TAP device or start GNU Radio). > > Hi Bastian.
Thanks a lot for your anwer. I got a computer and i'm try to communicate to it. When i configure Monitor mode i can get packages. I've tried interface ad-hoc mode I've checked the frame and it looks as supposed. It shows the MAC of the PC which is receiving, the MAC associated to the USRP and the common flags. I think it is a problem in the configuration file in the PC which is receiving. In that PC i'm doing the next: Turn off the interface: sudo ifconfig wlp2s0 down Set the mode sudo iwconfig wlp2s0 mode monitor/managed Turn on the interface: sudo ifconfig wlp2s0 up Set in the channel that USRP is going to send sudo iw dev wlp2s0 set freq 2472 Assign an IP in the network, the USRP is .1 sudo ifconfig wlp2s0 192.168.123.2 Modify the kernel's IPv4 network sudo route add -net 192.168.123.0/24 <http://192.168.123.0/24> wlp2s0 Set a static route sudo arp -s 192.168.123.1 12:34:56:78:90:ab -i wlp2s0 All the commands work, i checked with iwconfig, ifconfig, route, arp -a **arp -a** ? (192.168.123.1) at 12:34:56:78:90:ab [ether] PERM on wlp2s0 **route** Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.123.0 * 255.255.255.0 U 0 0 0 wlp2s0 **ifconfig** wlp2s0 Link encap:Ethernet HWaddr e0:ca:94:68:06:a7 inet addr:192.168.123.2 Bcast:192.168.123.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 **iwconfig** wlp2s0 IEEE 802.11 Mode:ad-hoc Frequency:2.462 GHz Then i don't catch the problem. Again, thanks a lot for your time, **Finally, May you share to me the configuration file that you used when you configure your PC in these experiments?** > Best, > Bastian > > > > : On modern Linuxes, it's usually > >> not a great idea to manipulate network config using ifconfig directly – >> NetworkManager tends to change things automagically if it doesn't think the >> link is functional (sometimes, even if it is). Please make sure your card >> is either unmanaged by NetworkManager, or set up the device like you want >> it to behave, and then activate the connection with `nmcli`. I'm not quite >> sure this is best solved on the discuss-gnuradio mailing list – we're not >> really linux networking setup experts :) >> >> Best regards, >> >> Marcus >> >> >> On 05/26/2017 07:18 AM, Cristian Rodríguez wrote: >> >>> >>> >>> 2017-05-19 7:04 GMT-05:00 Bastian Bloessl <m...@bastibl.net <mailto: >>> m...@bastibl.net>>: >>> >>> Hi, >>> >>> > On 19. May 2017, at 12:09, Cristian Rodríguez >>> <cristian.rodriguez...@gmail.com >>> <mailto:cristian.rodriguez...@gmail.com>> wrote: >>> > >>> > You will have to also add the corresponding entry in reverse >>> direction. It’s not in the script since I always used the WiFi >>> card of another PC. >>> >>> > I did that as follows: >>> > >>> > sudo arp -s 192.168.123.1 12:34:56:78:90:ab -i wlp4s0 >>> >>> So you just set up one ARP entry. >>> >>> >>> > >>> > Then use Wireshark to monitor GNU Radio (that’s what you might >>> do at the moment) and also the WiFi card. This might help to >>> understand what frames are actually sent, if they are OK (MAC, IP, >>> BSS) and if they are successfully received by the WiFi card and >>> the SDR. >>> > If i do a ping from the interface tap0 to 192.168.123.2 (IP of >>> my wifi card) it doesn't work. The signal is going out of the USRP >>> but the Wifi Card of the computer is not taking it. >>> > >>> > ping -I tap0 192.168.123.2 >>> > >>> > If i do a ping from the interface wlp4s0 to 192.168.123.1 (IP of >>> USRP B210) it doesn't work. The signal is NOT going out of the >>> Wifi card (i verifed that through wireshark). >>> > >>> > ping -I wlp4s0 192.168.123.1 >>> >>> As I said, you will have to actually look at the frame (BSS, MAC, >>> IP, …) and see if the fields are OK. Also put the receiver in >>> monitor mode to check if the packet is actually received. It’s a >>> configuration issue and you will have to find out where in the >>> network stack it gets dropped. >>> >>> I've tried to solve the trouble the whole week. I don't think my >>> computer is able to support the communication between its Wifi card and the >>> USRP B210. When i do a Ping from the USRP to the wifi card (in monitor >>> mode), and it receives the ping, it stops working and in the terminal which >>> is executing the app nic.sh appear *ether type: IP. *In the wireshark file >>> for the side of Tx, it clearly have stoped working. I've tried to solve it, >>> but i don't think is a configuration problem. >>> >>> On the other side, i got a computer and i'm try to communicate to it. >>> When i configure Monitor mode i can get packages. >>> >>> What interface Mode do you think i should use? Ad-hoc or managed? >>> >>> I've tried both but for me it doesn't work. >>> >>> I've checked the frame and it looks as supposed. It shows the MAC of the >>> PC which is receiving, the MAC associated to the USRP and the common flags. >>> >>> I think it is a problem in the configuration file in the PC which is >>> receiving. >>> In that PC i'm doing the next: >>> >>> Turn off the interface: >>> sudo ifconfig wlp2s0 down >>> Set the mode >>> sudo iwconfig wlp2s0 mode monitor/managed >>> Turn on the interface: >>> sudo ifconfig wlp2s0 up >>> Set in the channel that USRP is going to send >>> sudo iw dev wlp2s0 set freq 2472 >>> Assign an IP in the network, the USRP is .1 >>> sudo ifconfig wlp2s0 192.168.123.2 >>> Modify the kernel's IPv4 network >>> sudo route add -net 192.168.123.0/24 <http://192.168.123.0/24> wlp2s0 >>> Set a static route >>> sudo arp -s 192.168.123.1 12:34:56:78:90:ab -i wlp2s0 >>> >>> All the commands work, i checked with iwconfig, ifconfig, route, arp -a >>> >>> *arp -a* >>> ? (192.168.123.1) at 12:34:56:78:90:ab [ether] PERM on wlp2s0 >>> >>> *route* >>> Kernel IP routing table >>> Destination Gateway Genmask Flags Metric Ref Use >>> Iface >>> 192.168.123.0 * 255.255.255.0 U 0 0 0 >>> wlp2s0 >>> >>> *ifconfig* >>> wlp2s0 Link encap:Ethernet HWaddr e0:ca:94:68:06:a7 >>> inet addr:192.168.123.2 Bcast:192.168.123.255 >>> Mask:255.255.255.0 >>> UP BROADCAST MULTICAST MTU:1500 Metric:1 >>> >>> *iwconfig* >>> wlp2s0 IEEE 802.11 ESSID:off/any >>> Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated >>> Retry short limit:7 RTS thr:off Fragment thr:off >>> Power Management:on >>> >>> Then i don't catch the problem. >>> >>> *Finally, May you share to me the configuration file that you used when >>> you configure your PC in these experiments?* >>> >>> Really, thanks a lot for your time. >>> >>> Best regards, >>> >>> Cristian >>> >>
_______________________________________________ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
