Hi Steve, two things before I go into detail: * this is the GNU Radio mailing list; your problem is USRP-centric. Please consider using usrp-us...@lists.ettus.com for followups [1] where more experience with USRPs is concentrated * Doing high performance signal processing in a VM is problematic, and USB3 support of virtualizers is patchy to say the least. Also, considerable computational overhead might be added when virtualizing USB devices, but that really depends on how VirtualBox works internally (which I don't know).
This has happened to me, too. However, I was able to get things running by simply executing the b2xx_fx3_utils tool, which is probably installed somewhere like /usr/lib/uhd/utils on your system. Please do report back (to usrp-users) if you were able to fix the issue, and which USB3 controller (if you're using one at all) you're using; there are a lot of chipsets with faulty USB3 implementations, which is not something the B2x0 can fix... Greetings, Marcus [1] http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com On 12.08.2014 19:46, Steve wrote: > Greetings to the group > > This is another connection issue for the B210, however I think it somewhat > unique having tried the solutions provided for other users, although I am a > newbie so it could be something very obvious or I misunderstood previous > instructions. I am using -- > > Ubuntu 14.04 (VM VirtualBox) > GNURadio 3.7.3 > UHD 003.007.001 > (which I understand are the latest versions, from the repository and have > tried both stable and unstable versions). > > From a clean snapshot (without any GNU radio, python or UHD) and following > advice from the forums I performed the following installation sequence -- > > sudo apt-get install python python-wxgtk2.8 pyqt4-dev-tools python-qwt5-qt4 > python-numpy libboost-all-dev libusb-1.0.0-dev > sudo bash -c 'echo "deb > http://files.ettus.com/binaries/uhd_stable/repo/uhd/ubuntu/`lsb_release -cs` > `lsb_release -cs` main" > /etc/apt/sources.list.d/ettus.list' > sudo bash -c 'echo "deb > http://files.ettus.com/binaries/uhd_stable/repo/gnuradio/ubuntu/`lsb_release > -cs` `lsb_release -cs` main" >> /etc/apt/sources.list.d/ettus.list' > sudo apt-get update > sudo apt-get install -t `lsb_release -cs` uhd gnuradio > sudo apt-get install python-cheetah > > I get the report in gnuradio that the device cannot be found (I have tried > running both as sudo or as a normal user in case of permissions -- a bit new > to linux). When setup with just a UHD source and a FFT sink GNURadio returns: > RuntimeError: LookupError: KeyError: No devices found for -----> > Empty Device Address > > Seeing the solution provided in this mailing list I have tried to modify udev > rules as follows: > sudo gedit /lib/udev/rules.d/40-uhd-host.rules > SUBSYSTEMS=="usb", ATTRS{idVendor}=="2500", ATTRS{idProduct}=="0020", > GROUP:="usrp", MODE:="0660"I have also tried with the stable equivalent, > again from a fresh snapshot. > > When I run lsusb I can see the device 2500:0020 (sometimes) although it > frequently disappears. > Bus 001 Device 032: ID 2500:0020 > Bus 001 Device 007: ID 80ee:0021 VirtualBox USB Tablet > Bus 001 Device 006: ID 0bda:0129 Realtek Semiconductor Corp. RTS5129 Card > Reader Controller > Bus 001 Device 005: ID 0a5c:21d7 Broadcom Corp. BCM43142 Bluetooth 4.0 > Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > > Using sudo uhd_find_devices I get the following, which appears like it has > identified something as it tries to load image (unlike it not connected) but > then fails: > linux; GNU C++ version 4.8.2; Boost_105400; UHD_003.007.001-20-unstable > -- Loading firmware image: /usr/share/uhd/images/usrp_b200_fw.hex... done > No UHD Devices Found > > I am not sure why it is trying to load b200 when it is a b210 (4 ch)? I read > that using uhd_usrp_probe with an address might work but unsure how to do > this without an IP address. > > I have tried both powering through the USB only or providing 6V in case it is > a supply issue, noting in the second case a change in current draw once I > start trying to interact from 40 mA to 120 mA. > > Many thanks for any pointers -- > > Steve > > > > _______________________________________________ > Discuss-gnuradio mailing list > Discuss-gnuradio@gnu.org > https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
_______________________________________________ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
