So I checked all the pins in this daughtercard and they all look fine.
Could it be anything else?
Thanks any help,
Devin
Also, here is the output of uhd_usrp_probe
$ sudo uhd_usrp_probe --args="addr=192.168.10.2"
linux; GNU C++ version 4.4.5; Boost_104000; UHD_002.20110126204618.b83454d
Current recv sock buff size: 50000000 bytes
mboard0 MIMO master
Warning:
Unknown transceiver board ID combination...
RX dboard ID: WBX (0x0053)
TX dboard ID: Unknown (0xffff)
_____________________________________________________
/
| Device: USRP2/N Series device
| _____________________________________________________
| /
| | Mboard: USRP2-REV3 mboard
| | rev: 768
| | mac-addr: 00:50:c2:85:30:52
| | ip-addr: 255.255.255.255
| | serial: 82
| | name: dk-usrp2
| | _____________________________________________________
| | /
| | | RX DSP: USRP2-REV3 ddc0
| | | Codec Rate: 100.000000 Msps
| | _____________________________________________________
| | /
| | | TX DSP: USRP2-REV3 duc0
| | | Codec Rate: 100.000000 Msps
| | _____________________________________________________
| | /
| | | RX Dboard: USRP2-REV3 dboard (rx unit)
| | | _____________________________________________________
| | | /
| | | | RX Subdev: Unknown - WBX (0x0053)
| | | | Antennas:
| | | | Freq range: 0.000 to 0.000 Mhz
| | | | Gain Elements: None
| | | | Connection Type: C
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | RX Codec: USRP2-REV3 adc - ltc2284
| | | | Gain Elements: None
| | _____________________________________________________
| | /
| | | TX Dboard: USRP2-REV3 dboard (tx unit)
| | | _____________________________________________________
| | | /
| | | | TX Subdev: Unknown - Unknown (0xffff)
| | | | Antennas:
| | | | Freq range: 0.000 to 0.000 Mhz
| | | | Gain Elements: None
| | | | Connection Type: C
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | TX Codec: USRP2-REV3 dac - ad9777
| | | | Gain Elements: None
On Thu, Mar 10, 2011 at 2:18 PM, Marcus D. Leech <mle...@ripnet.com> wrote:
> On <03%2F10%2F2011> <03%2F10%2F2011>03/10/2011 02:10 PM, Josh Blum wrote:
>
>>
>> On <03%2F10%2F2011> <03%2F10%2F2011>03/10/2011 10:58 AM, devin kelly
>> wrote:
>>
>>> Hello,
>>>
>>> When using a particular WBX daughtercard I get this message from my
>>> script:
>>>
>>> Current recv sock buff size: 60000000 bytes
>>> mboard0 MIMO master
>>>
>>> Warning:
>>> Unknown transceiver board ID combination...
>>> RX dboard ID: WBX (0x0053)
>>> TX dboard ID: Unknown (0xffff)
>>>
>> This is usually a sign that the board is not mounted correctly. Re-mount
>> the WBX and try again.
>>
>> -Josh
>>
>>
>> He says that he tried it on multiple USRP motherboards, so it's unlikely
> to be, per se, a mounting issue. But I'd
> check for a bent pin on the daughtercard connector.
>
>
>
>
> --
> Marcus Leech
> Principal Investigator
> Shirleys Bay Radio Astronomy Consortium
> http://www.sbrac.org
>
>
>
>
> _______________________________________________
> Discuss-gnuradio mailing list
> Discuss-gnuradio@gnu.org
> http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>
--
http://users.wpi.edu/~dkelly/
_______________________________________________
Discuss-gnuradio mailing list
Discuss-gnuradio@gnu.org
http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
