Thanks Kent for looking at this.
I downloaded the image you sent and it gets stuck after I issue the bootefi
command. I let it sit for a few minutes and it never goes anywhere (console
output is pasted below)
You mentioned that "A reason why ELF works for seL4test and not for
camkes-arm-vm is potentially because the Elfloader doesn't get started in
monitor mode and is unable to start the kernel in Hyp mode. " What I don't
understand about that is that I have a couple of images that I built back
in August 2018 that still work just fine on this device when I use bootelf
to boot them. seL4 starts up and drops to the VM and I can log into the VM.
U-Boot SPL 2020.01-00442-gc00bd81ae0 (Jan 10 2020 - 11:10:18 -0500)
Trying to boot from RAM
U-Boot 2020.01-00442-gc00bd81ae0 (Jan 10 2020 - 11:10:18 -0500)
SoC: tegra124
Reset cause: POR
Model: NVIDIA Jetson TK1
Board: NVIDIA Jetson TK1
DRAM: 2 GiB
MMC: sdhci@700b0400: 1, sdhci@700b0600: 0
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
Tegra124 (Jetson TK1) # fatload mmc 1 ${loadaddr} capdl-loader-image-arm-tk1
20762864 bytes read in 974 ms (20.3 MiB/s)
Tegra124 (Jetson TK1) # bootefi ${loadaddr}
On Tue, Jan 28, 2020 at 8:05 PM Mcleod, Kent (Data61, Kensington NSW) <
[email protected]> wrote:
> Hi Mike,
> Here is a copy of an EFI binary for the camkes-arm-vm tk1 project that
> runs on our tk1 development board internally:
> https://cloudstor.aarnet.edu.au/plus/s/FHVMZi0ei1Q6IYA.
> A reason why ELF works for seL4test and not for camkes-arm-vm is
> potentially because the Elfloader doesn't get started in monitor mode and
> is unable to start the kernel in Hyp mode. Here is some output from our
> build logs:
> U-Boot 2019.04-00592-g6c5f8dd540 (Apr 24 2019 - 12:42:58 +1000)
>
> TEGRA124
> Model: NVIDIA Jetson TK1
> Board: NVIDIA Jetson TK1
> DRAM: 2 GiB
> MMC: sdhci@700b0400: 1, sdhci@700b0600: 0
> Loading Environment from MMC... OK
> In: serial
> Out: serial
> Err: serial
> Net: No ethernet found.
> Hit any key to stop autoboot: 2
> 0
> Tegra124 (Jetson TK1) # pci enum && setenv autoload no && dhcp && tftpboot
> 0x81000000 jetson1/sel4-image
> pci enum && setenv autoload no && dhcp && tftpboot 0x81000000
> jetson1/sel4-image
>
> Warning: eth_rtl8169 using MAC address from ROM
> BOOTP broadcast 1
> BOOTP broadcast 2
> BOOTP broadcast 3
> DHCP client bound to address 10.13.1.186 (1262 ms)
> Using eth_rtl8169 device
> TFTP from server 10.13.0.28; our IP address is 10.13.1.186
> Filename 'jetson1/sel4-image'.
> Load address: 0x81000000
> Loading: *
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> ##################################################
> 4 MiB/s
> done
> Bytes transferred = 20762864 (13cd0f0 hex)
> Tegra124 (Jetson TK1) # bootelf 0x81000000 || bootefi 0x81000000
> bootelf 0x81000000 || bootefi 0x81000000
> ## No elf image at address 0x81000000
> 7 8MMC: no card present
> Scanning disk [email protected]...
> Disk [email protected] not ready
> Scanning disk [email protected]...
> Found 3 disks
> WARNING: booting without device tree
> ## Starting EFI application at 81000000 ...
> ELF loader: monitor mode init done
> Copy monitor mode vector from fb6785bc to a7f00000 size 50
> Number of IRQs: 192
> Load seL4 in nonsecure HYP mode 600001da
> ELF-loader started on CPU: ARM Ltd. Cortex-A15 r3p3
> paddr=[fb671000..fca3efff]
> No DTB passed in from boot loader.
> Looking for DTB in CPIO archive...found at fb7423a4.
> Loaded DTB from fb7423a4.
> paddr=[80059000..80069fff]
> ELF-loading image 'kernel'
> paddr=[80000000..80058fff]
> vaddr=[e0000000..e0058fff]
> virt_entry=e0000000
> ELF-loading image 'capdl-loader'
> paddr=[8006a000..81442fff]
> vaddr=[10000..13e8fff]
> virt_entry=17b1c
> relocating from fb671000-fca3f000 to dec30000-dfffe000... size=0x13ce000
> (padded size = 0x13d0000)
> ELF loader relocated, continuing boot...
> Enabling hypervisor MMU and paging
> Jumping to kernel-image entry point...
>
> Bootstrapping kernel
> Total 28 IOASID set up
> Region [c to 28) for SMMU caps
> Booting all finished, dropped to user space
_______________________________________________
Devel mailing list
[email protected]
https://sel4.systems/lists/listinfo/devel
