[AMD Official Use Only - General] All, Today in edk2 open design meeting, we went through the draft of principles of the EDK2 module reconstruction for accommodating different archs (IA32, X64, Arm, AArch64, RiscV64, Loongson64 and etc.) or different vendors of the same arch (AMD/Intel to IA32 and X64).
@Ray Ni<mailto:ray...@intel.com> and @michael.d.kin...@intel.com<mailto:michael.d.kin...@intel.com> 1. We may need somewhere on edk2 repo or another place that can have PR for the easy review, please let me know where I can create the PR instead of reviewing this through dev mailing list. 2. I didn't mention using CPUID, Family ID or PCD to have the different code path for AMD and Intel. The reason is, * This decreases the readability of code. * That makes a confusing to the review process i. Says the maintainer/reviewer owns the package, however the patch is specific to AMD implementation but the change is in the file that mixes up Intel and AMD code. Then who is supposed the right person to give the reviewed-by? Perhaps the AMD edk2 module maintainers or reviewers is the proper person to give the reviewed-by for this case. Of course, other maintainers still can join the review process and give the comments. So to separate the arch-specific code in a arch-specific source file simplifies the review, even that is just a small delta between two implementations. ii. We can have the maintainers or reviewers for the entire module or *Amd* files only. So the maintainers/reviewers do not have to review the changes that only made for other archs. But they have to help reviewing the common code if that gets impact. 1. I didn't mention to have <phase><arch><basename> for the new module. I prefer we just inherit the original module name or file name so we can know the module or the source file has the different implementation for archs in the file browser (when the files are sorted in alphabet). Lets discuss this using PR if possible. Thanks Abner Below is the draft of principles: Preface: The principle is mainly for UefiCpuPKg, but the same principle maybe applied to the EDK2 module that has the processor architecture dependence (such as the BaseLib under MdePkg/Library). Most of the EDK2 modules under UefiCpuPkg were developed specifically to IA32/X64 architecture, that is necessary to reconstruct the folder or revise the source files to accommodate other processor architectures. The EDK2 module reconstruction is also required for accommodating the same-arch-but-different-vendor's implementation (e.g., Intel and AMD for the X86 based processors). The EDK2 module may be strictly developed based on the specific processor architecture. The new introduced implementation for other processor architectures may consider to have a separate EDK2 module instance. Not all of the EDK2 modules revising can exactly meet the principles listed below, that depends on the delta between the original EDK2 module and the implementation for the new introduced processor architecture. It may require the further discussions with EDK2 module maintainers. The [Arch] refers to the Processor Architecture. The [Module] refer to the EDK2 module. The [X86] refers to both IA32 and X64. The principles to create the X86 folder in the module: 1. When X86-vendor's implementation is introduced to the existing module: 1. The folder reconstruction: A-1. If the module is obviously used by IA32/X64 only * No need to create X86 folder * Create X86-vendor's stuff under the root directory of module A-2. If the existing module is expected to accommodate the different archs or the module already has multiple archs: * Create X86 folder * Create X86-vendor's stuff under X86 folder 1. The files reconstruction: B-1. The module INF metafile * The existing INF metafile should be kept without relocation. Should not have the impacts to the existing DSC/FDF file. * The new introduced INF metafile should be located under the root directory of module with the file naming format as below. This keeps the consistent module file structure. * <OriginalFileName><arch>.inf B-2. Source files The new arch implementation is introduced to the module in order to leverage the source code and the module design architecture, so * That is contributor's responsibility to review the source code and strip the arch-dependent code away and put it into the arch-specific file. Leave the common code in the original file if there is no arch-specific and arch-specific-feature wordings in the file name. Create a common file for the common implementation otherwise. * The file naming for the arch-specific file <OriginalFileName ><arch>.* * The file naming for the common implementation < OriginalFileNaming >Common.* * That is contributor's responsibility to relocate the arch-specific source files to the arch-specific folder. * That is contributor's responsibility to make sure the original INF metafile can properly pull-in the source file from arch-specific folder after the source file reconstruction. * The common source files should be located under the root directory of module 1. When a new arch's implementation is introduced to the existing module which was developed for the specific arch: 1. The folder reconstruction: * Create arch folder for the existing arch implementation * Create the arch folder for the new introduced arch 1. The files reconstruction: B-1. The module INF metafile * The existing INF file should be kept without the relocation. Should not have the impacts to the existing DSC/FDF file. * The new introduced INF metafile should be located under the root directory of module with the file naming format as below. This keeps the consistent module file structure. * < OriginalFileNaming><arch>.inf B-2. Source files The new arch implementation is introduced to this module in order to leverage the source code and the module design architecture, so * That is contributor's responsibility to review the source code and strip the arch-dependent code away and put it into the arch-specific file. Leave the common code in the original file if there is no arch-specific wording in the file name. Create a common file for the common implementation otherwise. * The file naming for the arch-specific source file < OriginalFileNaming ><arch>.* * The file naming for the common implementation <OriginalFileNaming>Common.* * That is contributor's responsibility to relocate the arch-specific source files to the arch-specific folder. * That is contributor's responsibility to make sure the original INF metafile can properly pull-in the source file from arch-specific folder after the source file reconstruction. * The common source files should be located under the root directory of module 1. When a new arch implementation has a huge delta with the original implementation Create a separate module instance. The naming of the module should follow below format, * Add the arch prefix with the original module name: < OriginalModuleNaming><arch> -=-=-=-=-=-=-=-=-=-=-=- Groups.io Links: You receive all messages sent to this group. View/Reply Online (#94226): https://edk2.groups.io/g/devel/message/94226 Mute This Topic: https://groups.io/mt/93872791/21656 Group Owner: devel+ow...@edk2.groups.io Unsubscribe: https://edk2.groups.io/g/devel/unsub [arch...@mail-archive.com] -=-=-=-=-=-=-=-=-=-=-=-
