Try: mount -t smartfs /dev/smart0 --> mount -t smartfs /dev/smart0 /mnt
On Mon, Mar 22, 2021 at 1:17 PM Flavio Castro Alves Filho <flavio.al...@gmail.com> wrote: > > Hello Alan, > > Enabling the CONFIG_BCH, I could finally run flash_eraseall and > mksmartfs commands. > > But the mount command is not working. > > Below there is my NuttX output: > > ABCDF > SmartFS initialized > INFO: mx25l MTD Flash driver initialized > up_rtc_getdatetime: Warning: PCF8563 RTC integrity is not guaranteed > (bit 7 in VL_SECONDS register is set) > . > NuttShell (NSH) NuttX-10.0.1 > nsh>flash_eraseall /dev/smart0 > nsh>mksmartfs /dev/smart0 > nsh>mount -t smartfs /dev/smart0 > nsh: mount: mount failed: 15 > nsh>cat /proc/fs/usage > Filesystem Size Used Available Mounted on > procfs 0B 0B 0B /proc > nsh> > > And here is my configuration file: > > CONFIG_ARCH="arm" > CONFIG_ARCH_BOARD="stm32f4discovery" > CONFIG_ARCH_BOARD_STM32F4_DISCOVERY=y > CONFIG_ARCH_CHIP="stm32" > CONFIG_ARCH_CHIP_STM32=y > CONFIG_ARCH_CHIP_STM32F407VG=y > CONFIG_ARCH_STACKDUMP=y > CONFIG_BCH=y > CONFIG_BOARDCTL_USBDEVCTRL=y > CONFIG_BOARD_LATE_INITIALIZE=y > CONFIG_BOARD_LOOPSPERMSEC=16717 > CONFIG_BUILTIN=y > CONFIG_C99_BOOL8=y > CONFIG_CDCACM=y > CONFIG_DEBUG_ERROR=y > CONFIG_DEBUG_FEATURES=y > CONFIG_DEBUG_HARDFAULT_ALERT=y > CONFIG_DEBUG_INFO=y > CONFIG_DEBUG_WARN=y > CONFIG_ETH0_PHY_LAN8742A=y > CONFIG_EXAMPLES_TCPECHO=y > CONFIG_FS_PROCFS=y > CONFIG_FS_PROCFS_REGISTER=y > CONFIG_FS_SMARTFS=y > CONFIG_HAVE_CXX=y > CONFIG_INTELHEX_BINARY=y > CONFIG_LIBCXX=y > CONFIG_LIBC_FLOATINGPOINT=y > CONFIG_LIBC_LOCALTIME=y > CONFIG_LIBM=y > CONFIG_MAX_TASKS=16 > CONFIG_MM_REGIONS=2 > CONFIG_MTD=y > CONFIG_MTD_MX25L=y > CONFIG_MTD_SMART=y > CONFIG_MTD_SMART_FSCK=y > CONFIG_NET=y > CONFIG_NETDB_DNSCLIENT=y > CONFIG_NETDEV_PHY_IOCTL=y > CONFIG_NETINIT_DHCPC=y > CONFIG_NETINIT_DNS=y > CONFIG_NETINIT_DNSIPADDR=0x08080808 > CONFIG_NETINIT_NOMAC=y > CONFIG_NETINIT_THREAD=y > CONFIG_NETUTILS_DHCPC=y > CONFIG_NET_BROADCAST=y > CONFIG_NET_ICMP=y > CONFIG_NET_ICMP_SOCKET=y > CONFIG_NET_LOCAL=y > CONFIG_NET_PKT=y > CONFIG_NET_SOCKOPTS=y > CONFIG_NET_TCP=y > CONFIG_NET_TCPBACKLOG=y > CONFIG_NET_TCP_KEEPALIVE=y > CONFIG_NET_UDP=y > CONFIG_NFILE_DESCRIPTORS=8 > CONFIG_NSH_BUILTIN_APPS=y > CONFIG_NSH_DISABLE_DATE=y > CONFIG_NSH_DISABLE_IFCONFIG=y > CONFIG_NSH_DISABLE_IFUPDOWN=y > CONFIG_NSH_DISABLE_LOSMART=y > CONFIG_NSH_DISABLE_PS=y > CONFIG_NSH_FILEIOSIZE=512 > CONFIG_PREALLOC_TIMERS=4 > CONFIG_PSEUDOFS_SOFTLINKS=y > CONFIG_RAM_SIZE=114688 > CONFIG_RAM_START=0x20000000 > CONFIG_RAW_BINARY=y > CONFIG_RR_INTERVAL=200 > CONFIG_RTC=y > CONFIG_RTC_EXTERNAL=y > CONFIG_RTC_PCF8563=y > CONFIG_SCHED_HPWORK=y > CONFIG_SCHED_ONEXIT=y > CONFIG_SCHED_ONEXIT_MAX=4 > CONFIG_SCHED_WAITPID=y > CONFIG_SDCLONE_DISABLE=y > CONFIG_SERIAL_TERMIOS=y > CONFIG_STACK_CANARIES=y > CONFIG_START_DAY=2 > CONFIG_START_MONTH=11 > CONFIG_START_YEAR=2012 > CONFIG_STM32F4DISBB=y > CONFIG_STM32_ETHMAC=y > CONFIG_STM32_I2C1=y > CONFIG_STM32_JTAG_SW_ENABLE=y > CONFIG_STM32_OTGFS=y > CONFIG_STM32_PHYADDR=0 > CONFIG_STM32_PHYSR=31 > CONFIG_STM32_PHYSR_100FD=0x0018 > CONFIG_STM32_PHYSR_100HD=0x0008 > CONFIG_STM32_PHYSR_10FD=0x0014 > CONFIG_STM32_PHYSR_10HD=0x0004 > CONFIG_STM32_PHYSR_ALTCONFIG=y > CONFIG_STM32_PHYSR_ALTMODE=0x001c > CONFIG_STM32_RMII_EXTCLK=y > CONFIG_STM32_SPI1=y > CONFIG_STM32_USART1=y > CONFIG_STM32_USART2=y > CONFIG_STM32_USART3=y > CONFIG_SYMTAB_ORDEREDBYNAME=y > CONFIG_SYSLOG_CONSOLE=y > CONFIG_SYSTEM_FLASH_ERASEALL=y > CONFIG_SYSTEM_NSH=y > CONFIG_SYSTEM_PING=y > CONFIG_USART1_SERIAL_CONSOLE=y > CONFIG_USART2_RXBUFSIZE=128 > CONFIG_USART2_TXBUFSIZE=128 > CONFIG_USART3_2STOP=1 > CONFIG_USART3_BAUD=9600 > CONFIG_USART3_RS485=y > CONFIG_USBDEV=y > CONFIG_USER_ENTRYPOINT="nsh_main" > > Am I still missing anything? > > What I realized is that the /mnt directory is not showing when I list > the directories on the root. Is it normal? > > Best regards, > > Flavio > > Em dom., 21 de mar. de 2021 às 12:22, Alan Carvalho de Assis > <acas...@gmail.com> escreveu: > > > > Hi Flavio, > > > > You need to enable also the CONFIG_BCH, some recent modification in > > the BCH created this side-effect. > > > > BR, > > > > Alan > > > > On 3/21/21, Flavio Castro Alves Filho <flavio.al...@gmail.com> wrote: > > > Hello, > > > > > > I am trying to use my stm32f4discovery board with MX25L800 dataflash > > > memory, through SPI and SmartFS file system. > > > > > > I installed a NuttX driver for this memory type and I am having > > > problems making this memory work. I cannot format the memory. > > > > > > Here is the output on the console, with FS Debug enabled and the commands > > > used: > > > > > > ABCDF > > > smart_scan: Entry > > > smart_scan: Scan sector 0 > > > ... > > > smart_scan: Scan sector 511 > > > smart_fsck: Entry > > > smart_fsck_directory: ERROR: Invalid phys sector 65535 > > > smart_readsector: Entry > > > smart_readsector: ERROR: Logical sector 0 not allocated > > > smart_scan: SMART Scan > > > smart_scan: Erase size: 4096 > > > smart_scan: Erase count: 256 > > > smart_scan: Sect/block: 2 > > > smart_scan: MTD Blk/Sect: 8 > > > SmartFS initialized > > > INFO: mx25l MTD Flash driver initialized > > > up_rtc_getdatetime: Warning: PCF8563 RTC integrity is not guaranteed > > > (bit 7 in VL_SECONDS register is set) > > > . > > > NuttShell (NSH) NuttX-10.0.1 > > > nsh>mksmartfs /dev/smart0 > > > nsh: mksmartfs: mksmartfs failed: 2 > > > nsh>flash_eraseall /dev/smart0 > > > flash_eraseall: ERROR: Failed to open '/dev/smart0': 6 > > > nsh> > > > > > > Can anybody give me any advice on where to start searching for the > > > solution? > > > > > > Here is my configuration file: > > > > > > CONFIG_ARCH="arm" > > > CONFIG_ARCH_BOARD="stm32f4discovery" > > > CONFIG_ARCH_BOARD_STM32F4_DISCOVERY=y > > > CONFIG_ARCH_CHIP="stm32" > > > CONFIG_ARCH_CHIP_STM32=y > > > CONFIG_ARCH_CHIP_STM32F407VG=y > > > CONFIG_ARCH_STACKDUMP=y > > > CONFIG_BOARDCTL_USBDEVCTRL=y > > > CONFIG_BOARD_LATE_INITIALIZE=y > > > CONFIG_BOARD_LOOPSPERMSEC=16717 > > > CONFIG_BUILTIN=y > > > CONFIG_C99_BOOL8=y > > > CONFIG_CDCACM=y > > > CONFIG_DEBUG_ERROR=y > > > CONFIG_DEBUG_FEATURES=y > > > CONFIG_DEBUG_FS=y > > > CONFIG_DEBUG_FS_ERROR=y > > > CONFIG_DEBUG_FS_INFO=y > > > CONFIG_DEBUG_FS_WARN=y > > > CONFIG_DEBUG_HARDFAULT_ALERT=y > > > CONFIG_DEBUG_INFO=y > > > CONFIG_DEBUG_WARN=y > > > CONFIG_ETH0_PHY_LAN8742A=y > > > CONFIG_EXAMPLES_TCPECHO=y > > > CONFIG_FS_PROCFS=y > > > CONFIG_FS_PROCFS_REGISTER=y > > > CONFIG_FS_SMARTFS=y > > > CONFIG_HAVE_CXX=y > > > CONFIG_INTELHEX_BINARY=y > > > CONFIG_LIBCXX=y > > > CONFIG_LIBC_FLOATINGPOINT=y > > > CONFIG_LIBC_LOCALTIME=y > > > CONFIG_LIBM=y > > > CONFIG_MAX_TASKS=16 > > > CONFIG_MM_REGIONS=2 > > > CONFIG_MTD=y > > > CONFIG_MTD_MX25L=y > > > CONFIG_MTD_SMART=y > > > CONFIG_MTD_SMART_FSCK=y > > > CONFIG_NET=y > > > CONFIG_NETDB_DNSCLIENT=y > > > CONFIG_NETDEV_PHY_IOCTL=y > > > CONFIG_NETINIT_DHCPC=y > > > CONFIG_NETINIT_DNS=y > > > CONFIG_NETINIT_DNSIPADDR=0x08080808 > > > CONFIG_NETINIT_NOMAC=y > > > CONFIG_NETINIT_THREAD=y > > > CONFIG_NETUTILS_DHCPC=y > > > CONFIG_NET_BROADCAST=y > > > CONFIG_NET_ICMP=y > > > CONFIG_NET_ICMP_SOCKET=y > > > CONFIG_NET_LOCAL=y > > > CONFIG_NET_PKT=y > > > CONFIG_NET_SOCKOPTS=y > > > CONFIG_NET_TCP=y > > > CONFIG_NET_TCPBACKLOG=y > > > CONFIG_NET_TCP_KEEPALIVE=y > > > CONFIG_NET_UDP=y > > > CONFIG_NFILE_DESCRIPTORS=8 > > > CONFIG_NSH_BUILTIN_APPS=y > > > CONFIG_NSH_DISABLE_DATE=y > > > CONFIG_NSH_DISABLE_IFCONFIG=y > > > CONFIG_NSH_DISABLE_IFUPDOWN=y > > > CONFIG_NSH_DISABLE_LOSMART=y > > > CONFIG_NSH_DISABLE_PS=y > > > CONFIG_NSH_FILEIOSIZE=512 > > > CONFIG_PREALLOC_TIMERS=4 > > > CONFIG_PSEUDOFS_SOFTLINKS=y > > > CONFIG_RAM_SIZE=114688 > > > CONFIG_RAM_START=0x20000000 > > > CONFIG_RAW_BINARY=y > > > CONFIG_RR_INTERVAL=200 > > > CONFIG_RTC=y > > > CONFIG_RTC_EXTERNAL=y > > > CONFIG_RTC_PCF8563=y > > > CONFIG_SCHED_HPWORK=y > > > CONFIG_SCHED_ONEXIT=y > > > CONFIG_SCHED_ONEXIT_MAX=4 > > > CONFIG_SCHED_WAITPID=y > > > CONFIG_SDCLONE_DISABLE=y > > > CONFIG_SERIAL_TERMIOS=y > > > CONFIG_STACK_CANARIES=y > > > CONFIG_START_DAY=2 > > > CONFIG_START_MONTH=11 > > > CONFIG_START_YEAR=2012 > > > CONFIG_STM32F4DISBB=y > > > CONFIG_STM32_ETHMAC=y > > > CONFIG_STM32_I2C1=y > > > CONFIG_STM32_JTAG_SW_ENABLE=y > > > CONFIG_STM32_OTGFS=y > > > CONFIG_STM32_PHYADDR=0 > > > CONFIG_STM32_PHYSR=31 > > > CONFIG_STM32_PHYSR_100FD=0x0018 > > > CONFIG_STM32_PHYSR_100HD=0x0008 > > > CONFIG_STM32_PHYSR_10FD=0x0014 > > > CONFIG_STM32_PHYSR_10HD=0x0004 > > > CONFIG_STM32_PHYSR_ALTCONFIG=y > > > CONFIG_STM32_PHYSR_ALTMODE=0x001c > > > CONFIG_STM32_RMII_EXTCLK=y > > > CONFIG_STM32_SPI1=y > > > CONFIG_STM32_USART1=y > > > CONFIG_STM32_USART2=y > > > CONFIG_STM32_USART3=y > > > CONFIG_SYMTAB_ORDEREDBYNAME=y > > > CONFIG_SYSLOG_CONSOLE=y > > > CONFIG_SYSTEM_FLASH_ERASEALL=y > > > CONFIG_SYSTEM_NSH=y > > > CONFIG_SYSTEM_PING=y > > > CONFIG_USART1_SERIAL_CONSOLE=y > > > CONFIG_USART2_RXBUFSIZE=128 > > > CONFIG_USART2_TXBUFSIZE=128 > > > CONFIG_USART3_2STOP=1 > > > CONFIG_USART3_BAUD=9600 > > > CONFIG_USART3_RS485=y > > > CONFIG_USBDEV=y > > > CONFIG_USER_ENTRYPOINT="nsh_main" > > > > > > Best regards, > > > > > > Flavio > > > > > > > > > -- > > > Flavio de Castro Alves Filho > > > > > > flavio.al...@gmail.com > > > Twitter: http://twitter.com/#!/fraviofii > > > LinkedIn profile: www.linkedin.com/in/flaviocastroalves > > > > > > > -- > Flavio de Castro Alves Filho > > flavio.al...@gmail.com > Twitter: http://twitter.com/#!/fraviofii > LinkedIn profile: www.linkedin.com/in/flaviocastroalves
