Xiang, Looks like attachments aren't making it through for some reason. Would you be willing to just paste the config into an email message?
BTW my ethernet interface isn't getting a MAC address... it's all 0's. Your virtual ethernet has one. So something is wrong with the netinit for my interface. cheers adam On Mon, Feb 10, 2020 at 10:03 PM Xiang Xiao <xiaoxiang781...@gmail.com> wrote: > It's my full config, but to avoid the LittleVGL downloading, I remove > some graphic related config. > Here is my output with the latest mainline: > xiaoxiang@xiaoxiang-VirtualBox:~/nuttx/nuttx$ sudo ./nuttx > > NuttShell (NSH) NuttX-8.2 > nsh> ps > PID GROUP PRI POLICY TYPE NPX STATE EVENT SIGMASK > STACK USED FILLED COMMAND > 0 0 0 FIFO Kthread N-- Ready 00000000 > 000000 000000 0.0% Idle Task > 1 1 224 FIFO Kthread --- Waiting Signal 00000000 > 002032 000460 22.6% hpwork > 2 1 100 FIFO Kthread --- Waiting Signal 00000000 > 002032 000924 45.4% lpwork > 3 1 100 FIFO Task --- Running 00000000 > 004080 002096 51.3% init > 5 4 100 FIFO Task --- Waiting Semaphore 00000010 > 002000 000804 40.2% Telnet daemon 0x56623690 > 6 4 100 FIFO Task --- Waiting Semaphore 00000010 > 002000 000804 40.2% Telnet daemon 0x56624510 > 7 4 100 FIFO Task --- Waiting Semaphore 00000000 > 002016 001828 90.6%! NTP daemon > nsh> ifconfig > eth0 Link encap:Ethernet HWaddr 42:09:36:15:9c:19 at UP > inet addr:10.0.2.18 DRaddr:10.0.2.2 Mask:255.255.255.0 > inet6 addr: fe80::4009:36ff:fe15:9c19/64 > inet6 DRaddr: ::/64 > > RX: Received Fragment Errors > 00000014 00000000 00000000 > IPv4 IPv6 ARP Dropped > 00000003 00000010 00000001 00000000 > TX: Queued Sent Errors Timeouts > 00000012 00000012 00000000 00000000 > Total Errors: 00000000 > > lo Link encap:Local Loopback at UP > inet addr:127.0.0.1 DRaddr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 > inet6 DRaddr: ::1/128 > > RX: Received Fragment Errors > 00000000 00000000 00000000 > IPv4 IPv6 ARP Dropped > 00000000 00000000 00000000 00000000 > TX: Queued Sent Errors Timeouts > 00000000 00000000 00000000 00000000 > Total Errors: 00000000 > > IPv4 IPv6 TCP UDP ICMP ICMPv6 > Received 0003 0010 0000 0009 0000 000a > Dropped 0000 0000 0000 0000 0000 0008 > IPv4 VHL: 0000 Frg: 0000 > IPv6 VHL: 0000 > Checksum 0000 ---- 0000 0000 ---- ---- > TCP ACK: 0000 SYN: 0000 > RST: 0000 0000 > Type 0000 0000 ---- ---- 0000 0007 > Sent 0006 000d 0000 0006 0000 000d > Rexmit ---- ---- 0000 ---- ---- ---- > nsh> ping www.google.com > PING 216.58.200.68 56 bytes of data > 56 bytes from 216.58.200.68: icmp_seq=0 time=240 ms > 56 bytes from 216.58.200.68: icmp_seq=1 time=220 ms > 56 bytes from 216.58.200.68: icmp_seq=2 time=210 ms > 56 bytes from 216.58.200.68: icmp_seq=3 time=210 ms > 56 bytes from 216.58.200.68: icmp_seq=4 time=210 ms > 56 bytes from 216.58.200.68: icmp_seq=5 time=160 ms > 56 bytes from 216.58.200.68: icmp_seq=6 time=120 ms > 56 bytes from 216.58.200.68: icmp_seq=7 time=120 ms > 56 bytes from 216.58.200.68: icmp_seq=8 time=260 ms > 56 bytes from 216.58.200.68: icmp_seq=9 time=130 ms > 10 packets transmitted, 10 received, 0% packet loss, time 10100 ms > > > On Tue, Feb 11, 2020 at 1:38 PM Adam Feuer <a...@starcat.io> wrote: > > > > Thank you Xiang. > > > > I tried your config options, but the simulator still crashes when I do a > > ping. > > > > You didn't attach a whole config file– would you be willing to send one? > > > > cheers > > adam > > > > On Mon, Feb 10, 2020 at 8:50 PM Xiang Xiao <xiaoxiang781...@gmail.com> > > wrote: > > > > > Do you enable CONFIG_SIM_NET_BRIDGE? > > > To get the basic network, the below options are required: > > > CONFIG_NET=y > > > > > > CONFIG_NETINIT_DHCPC=y > > > CONFIG_NETUTILS_DHCPC=y > > > > > > CONFIG_NET_ICMP=y > > > CONFIG_NET_ICMP_SOCKET=y > > > > > > CONFIG_NET_UDP=y > > > CONFIG_NET_UDP_BINDTODEVICE=y > > > > > > CONFIG_SIM_NET_BRIDGE=y > > > > > > CONFIG_SYSTEM_PING=y > > > > > > IPv6 need more options: > > > CONFIG_NET_ICMPv6=y > > > CONFIG_NET_ICMPv6_AUTOCONF=y > > > CONFIG_NET_ICMPv6_SOCKET=y > > > > > > CONFIG_NET_IPv6=y > > > > > > CONFIG_SYSTEM_PING6=y > > > > > > Anyway, you can try the attached config which has more options to get > > > the better network. > > > > > > > > > On Tue, Feb 11, 2020 at 12:22 PM Adam Feuer <a...@starcat.io> wrote: > > > > > > > > Xiang, > > > > > > > > Thanks for the tips! I tried to get this working, but I don't see any > > > > network interfaces on my nuttx system other than loopback. > > > > > > > > I ran the script on my Linux box, it created a nuttx0: interface > with an > > > IP > > > > address. But on the nuttx simulator all I see is this: > > > > > > > > nsh> ifconfig > > > > > lo Link encap:Local Loopback at UP > > > > > inet addr:127.0.0.1 DRaddr:127.0.0.1 Mask:255.0.0.0 > > > > > > > > > > > > > > > > > > > > Do you have a defconfig that I can run that will bring up NSH? Or > any > > > > defconfig that will show the network is working? > > > > > > > > cheers > > > > adam > > > > > > > > > > > > > > > > On Mon, Feb 10, 2020 at 7:45 PM Xiang Xiao < > xiaoxiang781...@gmail.com> > > > > wrote: > > > > > > > > > Adam, please follow this instruction if you want to connect the > real > > > > > network instead loopback: > > > > > > > > > > > > > > https://github.com/apache/incubator-nuttx/pull/249/commits/1b489449f790c2b4618df9133114bb05f0132e87 > > > > > The setup is very simple, you don't need config any IP address > > > manually. > > > > > > > > > > Thanks > > > > > Xiang > > > > > > > > > > On Tue, Feb 11, 2020 at 2:23 AM Gregory Nutt <spudan...@gmail.com> > > > wrote: > > > > > > > > > > > > > > > > > > > I'm trying to get the NuttX simulator working with TCP/IP > > > networking. I > > > > > > > used the sim:nsh defconfig as a base, then used "make > menuconfig" > > > to > > > > > select > > > > > > > TCP/IP, ICMP, and ping commands. > > > > > > > > > > > > > > My host is Ubuntu 19.10 Eoan. I installed bridge-utils and > > > configured a > > > > > > > bridge device nuttx0 and gave it an IP address 10.0.1.1. From > > > linux I > > > > > can > > > > > > > ping the bridge. > > > > > > > > > > > > > > I can compile and run the simulator. Commands seem to work. I > can > > > > > configure > > > > > > > the eth0 interface with IP address 10.0.1.2 and bring it up > using > > > > > ifup. But > > > > > > > when I try to ping the bridge, the nuttx simulator immediately > > > exits > > > > > with > > > > > > > no messages. > > > > > > > > > > > > > > I checked the .config against the sim:nettest defconfig, and my > > > > > settings in > > > > > > > .config match that one. > > > > > > > > > > > > > > What am I doing wrong? How do I debug this? > > > > > > > > > > > > I don't use TCP/IP networking with the simulator. Perhaps Xiao > Xiang > > > > > > will respond later. > > > > > > > > > > > > I am creating a simulator example that runs the TCP blaster > example > > > > > > using the loopback 127.0.0.1 device. I will give that to you > once I > > > > > > verify it. > > > > > > > > > > > > > > > > > > > > > > > > > > > > > -- > > > > Adam Feuer <a...@starcat.io> > > > > > > > > > -- > > Adam Feuer <a...@starcat.io> > -- Adam Feuer <a...@starcat.io>
