> -----Original Message-----
> From: Laurent Hardy [mailto:laurent.ha...@6wind.com]
> Sent: Thursday, April 27, 2017 11:04 PM
> To: dev@dpdk.org; Dai, Wei <wei....@intel.com>
> Cc: Yigit, Ferruh <ferruh.yi...@intel.com>; Zhang, Helin
> <helin.zh...@intel.com>; Ananyev, Konstantin
> <konstantin.anan...@intel.com>; olivier.m...@6wind.com
> Subject: [PATCH v4] net/ixgbe: ensure link status is updated
>
> In case of fiber and link speed set to 1Gb at peer side (with autoneg
> or with defined speed), link status could be not properly updated at
> time cable is plugged-in.
> Indeed if cable was not plugged when device has been configured and
> started then link status will not be updated properly with new speed
> as no link setup will be triggered.
>
> To avoid this issue, IXGBE_FLAG_NEED_LINK_CONFIG is set to try a link
> setup each time link_update() is triggered and current link status is
> down. When cable is plugged-in, link setup will be performed via
> ixgbe_setup_link().
>
> Signed-off-by: Laurent Hardy <laurent.ha...@6wind.com>
Acked-by: Wei Dai <wei....@intel.com>
> ---
> Hi Wei, please find enclosed patch v4, tested using testpmd.
>
> v1 -> v2:
> - rebase on top of head (change flag to 1<<4)
> - fix regression with copper links: only update link for fiber links
>
> v2 -> v3:
> - remove unnescessary check on speed mask if autoneg is false
>
> v3 -> v4:
> - remove default speed set to 10Gb if autoneg is false, rely on
> ixgbe_get_link_capabilities( ) instead.
> ---
> drivers/net/ixgbe/ixgbe_ethdev.c | 14 ++++++++++++++
> drivers/net/ixgbe/ixgbe_ethdev.h | 1 +
> 2 files changed, 15 insertions(+)
>
> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
> b/drivers/net/ixgbe/ixgbe_ethdev.c
> index 7b856bb..8a0c0a7 100644
> --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> @@ -3782,8 +3782,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev,
> int wait_to_complete)
> struct ixgbe_hw *hw =
> IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> struct rte_eth_link link, old;
> ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
> + struct ixgbe_interrupt *intr =
> + IXGBE_DEV_PRIVATE_TO_INTR(dev->data->dev_private);
> int link_up;
> int diag;
> + u32 speed = 0;
> + bool autoneg = false;
>
> link.link_status = ETH_LINK_DOWN;
> link.link_speed = 0;
> @@ -3793,6 +3797,14 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev,
> int wait_to_complete)
>
> hw->mac.get_link_status = true;
>
> + if ((intr->flags & IXGBE_FLAG_NEED_LINK_CONFIG) &&
> + hw->mac.ops.get_media_type(hw) == ixgbe_media_type_fiber) {
> + speed = hw->phy.autoneg_advertised;
> + if (!speed)
> + ixgbe_get_link_capabilities(hw, &speed, &autoneg);
> + ixgbe_setup_link(hw, speed, true);
> + }
> +
> /* check if it needs to wait to complete, if lsc interrupt is enabled */
> if (wait_to_complete == 0 || dev->data->dev_conf.intr_conf.lsc != 0)
> diag = ixgbe_check_link(hw, &link_speed, &link_up, 0);
> @@ -3810,10 +3822,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev,
> int wait_to_complete)
>
> if (link_up == 0) {
> rte_ixgbe_dev_atomic_write_link_status(dev, &link);
> + intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
> if (link.link_status == old.link_status)
> return -1;
> return 0;
> }
> + intr->flags &= ~IXGBE_FLAG_NEED_LINK_CONFIG;
> link.link_status = ETH_LINK_UP;
> link.link_duplex = ETH_LINK_FULL_DUPLEX;
>
> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.h
> b/drivers/net/ixgbe/ixgbe_ethdev.h
> index 5176b02..b576a6f 100644
> --- a/drivers/net/ixgbe/ixgbe_ethdev.h
> +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
> @@ -45,6 +45,7 @@
> #define IXGBE_FLAG_MAILBOX (uint32_t)(1 << 1)
> #define IXGBE_FLAG_PHY_INTERRUPT (uint32_t)(1 << 2)
> #define IXGBE_FLAG_MACSEC (uint32_t)(1 << 3)
> +#define IXGBE_FLAG_NEED_LINK_CONFIG (uint32_t)(1 << 4)
>
> /*
> * Defines that were not part of ixgbe_type.h as they are not used by the
> --
> 2.1.4
