This patch adds hwrm_func_cfg API which allows the configuration
of a child VF by its parent PF driver. It an also be used to configure a
PF by its corresponding PF driver.
Signed-off-by: Ajit Khaparde <ajit.khapa...@broadcom.com>
---
drivers/net/bnxt/hsi_struct_def_dpdk.h | 427 +++++++++++++++++++++++++++++++++
1 file changed, 427 insertions(+)
diff --git a/drivers/net/bnxt/hsi_struct_def_dpdk.h
b/drivers/net/bnxt/hsi_struct_def_dpdk.h
index f024837..0635dd2 100644
--- a/drivers/net/bnxt/hsi_struct_def_dpdk.h
+++ b/drivers/net/bnxt/hsi_struct_def_dpdk.h
@@ -88,6 +88,7 @@ struct ctx_hw_stats64 {
#define HWRM_FUNC_RESET (UINT32_C(0x11))
#define HWRM_FUNC_QCAPS (UINT32_C(0x15))
#define HWRM_FUNC_QCFG (UINT32_C(0x16))
+#define HWRM_FUNC_CFG (UINT32_C(0x17))
#define HWRM_FUNC_DRV_UNRGTR (UINT32_C(0x1a))
#define HWRM_FUNC_DRV_RGTR (UINT32_C(0x1d))
#define HWRM_PORT_PHY_CFG (UINT32_C(0x20))
@@ -2261,6 +2262,432 @@ struct hwrm_func_qcfg_output {
*/
} __attribute__((packed));
+/* hwrm_func_cfg */
+/*
+ * Description: This command allows configuration of a PF by the corresponding
+ * PF driver. This command also allows configuration of a child VF by its
parent
+ * PF driver. The input FID value is used to indicate what function is being
+ * configured. This allows a PF driver to configure the PF owned by itself or a
+ * virtual function that is a child of the PF. This command allows to reserve
+ * resources for a VF by its parent PF. To reverse the process, the command
+ * should be called with all enables flags cleared for resources. This will
free
+ * allocated resources for the VF and return them to the resource pool. If this
+ * command is requested by a VF driver to configure or reserve resources, then
+ * the HWRM shall fail this command. If default MAC address and/or VLAN are
+ * provided in this command, then the HWRM shall set up appropriate MAC/VLAN
+ * filters for the function that is being configured. If source properties
+ * checks are enabled and default MAC address and/or IP address are provided in
+ * this command, then the HWRM shall set appropriate source property checks
+ * based on provided MAC and/or IP addresses. The parent PF driver should not
+ * set MTU/MRU for a VF using this command. This is to allow MTU/MRU setting by
+ * the VF driver. If the MTU or MRU for a VF is set by the PF driver, then the
+ * HWRM should ignore it. A function's MTU/MRU should be set prior to
allocating
+ * RX VNICs or TX rings. A PF driver calls hwrm_func_cfg to allocate resources
+ * for itself or its children VFs. All function drivers shall call
hwrm_func_cfg
+ * to reserve resources. A request to hwrm_func_cfg may not be fully granted;
+ * that is, a request for resources may be larger than what can be supported by
+ * the device and the HWRM will allocate the best set of resources available,
+ * but that may be less than requested. If all the amounts requested could not
+ * be fulfilled, the HWRM shall allocate what it could and return a status code
+ * of success. A function driver should call hwrm_func_qcfg immediately after
+ * hwrm_func_cfg to determine what resources were assigned to the configured
+ * function. A call by a PF driver to hwrm_func_cfg to allocate resources for
+ * itself shall only allocate resources for the PF driver to use, not for its
+ * children VFs. Likewise, a call to hwrm_func_qcfg shall return the resources
+ * available for the PF driver to use, not what is available to its children
+ * VFs.
+ */
+/* Input (88 bytes) */
+struct hwrm_func_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being configured. If set
+ * to 0xFF... (All Fs), then the the configuration is for the
+ * requesting function.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t flags;
+ /*
+ * When this bit is '1', the function is disabled with source
+ * MAC address check. This is an anti-spoofing check. If this
+ * flag is set, then the function shall be configured to
+ * disallow transmission of frames with the source MAC address
+ * that is configured for this function.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_SRC_MAC_ADDR_CHECK_DISABLE \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', the function is enabled with source MAC
+ * address check. This is an anti-spoofing check. If this flag
+ * is set, then the function shall be configured to allow
+ * transmission of frames with the source MAC address that is
+ * configured for this function.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_SRC_MAC_ADDR_CHECK_ENABLE \
+ UINT32_C(0x2)
+ /* reserved */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_RSVD_MASK UINT32_C(0x1fc)
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_RSVD_SFT 2
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then standard TX ring mode is requested to be
+ * enabled on the function being configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_STD_TX_RING_MODE_ENABLE \
+ UINT32_C(0x200)
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then the standard TX ring mode is requested to be
+ * disabled on the function being configured. In this extended
+ * TX ring resource mode, the minimum and maximum bandwidth
+ * settings are not supported to allow the allocation of TX
+ * rings to span multiple scheduler nodes.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_STD_TX_RING_MODE_DISABLE \
+ UINT32_C(0x400)
+ uint32_t enables;
+ /* This bit must be '1' for the mtu field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MTU UINT32_C(0x1)
+ /* This bit must be '1' for the mru field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MRU UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the num_rsscos_ctxs field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_RSSCOS_CTXS UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the num_cmpl_rings field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_CMPL_RINGS UINT32_C(0x8)
+ /* This bit must be '1' for the num_tx_rings field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_TX_RINGS UINT32_C(0x10)
+ /* This bit must be '1' for the num_rx_rings field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_RX_RINGS UINT32_C(0x20)
+ /* This bit must be '1' for the num_l2_ctxs field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_L2_CTXS UINT32_C(0x40)
+ /* This bit must be '1' for the num_vnics field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_VNICS UINT32_C(0x80)
+ /*
+ * This bit must be '1' for the num_stat_ctxs field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_STAT_CTXS UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the dflt_mac_addr field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_MAC_ADDR UINT32_C(0x200)
+ /* This bit must be '1' for the dflt_vlan field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_VLAN UINT32_C(0x400)
+ /* This bit must be '1' for the dflt_ip_addr field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_IP_ADDR UINT32_C(0x800)
+ /* This bit must be '1' for the min_bw field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MIN_BW UINT32_C(0x1000)
+ /* This bit must be '1' for the max_bw field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MAX_BW UINT32_C(0x2000)
+ /*
+ * This bit must be '1' for the async_event_cr field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_ASYNC_EVENT_CR UINT32_C(0x4000)
+ /*
+ * This bit must be '1' for the vlan_antispoof_mode field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_VLAN_ANTISPOOF_MODE UINT32_C(0x8000)
+ /*
+ * This bit must be '1' for the allowed_vlan_pris field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_ALLOWED_VLAN_PRIS UINT32_C(0x10000)
+ /* This bit must be '1' for the evb_mode field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_EVB_MODE UINT32_C(0x20000)
+ /*
+ * This bit must be '1' for the num_mcast_filters field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_MCAST_FILTERS UINT32_C(0x40000)
+ /*
+ * This bit must be '1' for the num_hw_ring_grps field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_HW_RING_GRPS UINT32_C(0x80000)
+ uint16_t mtu;
+ /*
+ * The maximum transmission unit of the function. The HWRM
+ * should make sure that the mtu of the function does not exceed
+ * the mtu of the physical port that this function is associated
+ * with. In addition to configuring mtu per function, it is
+ * possible to configure mtu per transmit ring. By default, the
+ * mtu of each transmit ring associated with a function is equal
+ * to the mtu of the function. The HWRM should make sure that
+ * the mtu of each transmit ring that is assigned to a function
+ * has a valid mtu.
+ */
+ uint16_t mru;
+ /*
+ * The maximum receive unit of the function. The HWRM should
+ * make sure that the mru of the function does not exceed the
+ * mru of the physical port that this function is associated
+ * with. In addition to configuring mru per function, it is
+ * possible to configure mru per vnic. By default, the mru of
+ * each vnic associated with a function is equal to the mru of
+ * the function. The HWRM should make sure that the mru of each
+ * vnic that is assigned to a function has a valid mru.
+ */
+ uint16_t num_rsscos_ctxs;
+ /* The number of RSS/COS contexts requested for the function. */
+ uint16_t num_cmpl_rings;
+ /*
+ * The number of completion rings requested for the function.
+ * This does not include the rings allocated to any children
+ * functions if any.
+ */
+ uint16_t num_tx_rings;
+ /*
+ * The number of transmit rings requested for the function. This
+ * does not include the rings allocated to any children
+ * functions if any.
+ */
+ uint16_t num_rx_rings;
+ /*
+ * The number of receive rings requested for the function. This
+ * does not include the rings allocated to any children
+ * functions if any.
+ */
+ uint16_t num_l2_ctxs;
+ /* The requested number of L2 contexts for the function. */
+ uint16_t num_vnics;
+ /* The requested number of vnics for the function. */
+ uint16_t num_stat_ctxs;
+ /* The requested number of statistic contexts for the function. */
+ uint16_t num_hw_ring_grps;
+ /*
+ * The number of HW ring groups that should be reserved for this
+ * function.
+ */
+ uint8_t dflt_mac_addr[6];
+ /* The default MAC address for the function being configured. */
+ uint16_t dflt_vlan;
+ /*
+ * The default VLAN for the function being configured. This
+ * field's format is same as 802.1Q Tag's Tag Control
+ * Information (TCI) format that includes both Priority Code
+ * Point (PCP) and VLAN Identifier (VID).
+ */
+ uint32_t dflt_ip_addr[4];
+ /*
+ * The default IP address for the function being configured.
+ * This address is only used in enabling source property check.
+ */
+ uint32_t min_bw;
+ /*
+ * Minimum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_BITS (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_BYTES (UINT32_C(0x1) << 28)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_LAST \
+ FUNC_CFG_INPUT_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_LAST \
+ FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t max_bw;
+ /*
+ * Maximum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_BITS (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_BYTES (UINT32_C(0x1) << 28)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_LAST \
+ FUNC_CFG_INPUT_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_LAST \
+ FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint16_t async_event_cr;
+ /*
+ * ID of the target completion ring for receiving asynchronous
+ * event completions. If this field is not valid, then the HWRM
+ * shall use the default completion ring of the function that is
+ * being configured as the target completion ring for providing
+ * any asynchronous event completions for that function. If this
+ * field is valid, then the HWRM shall use the completion ring
+ * identified by this ID as the target completion ring for
+ * providing any asynchronous event completions for the function
+ * that is being configured.
+ */
+ uint8_t vlan_antispoof_mode;
+ /* VLAN Anti-spoofing mode. */
+ /* No VLAN anti-spoofing checks are enabled */
+ #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_NOCHECK UINT32_C(0x0)
+ /* Validate VLAN against the configured VLAN(s) */
+ #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_VALIDATE_VLAN \
+ UINT32_C(0x1)
+ /* Insert VLAN if it does not exist, otherwise discard */
+ #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_INSERT_IF_VLANDNE \
+ UINT32_C(0x2)
+ /*
+ * Insert VLAN if it does not exist, override
+ * VLAN if it exists
+ */
+ #define \
+ HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_INSERT_OR_OVERRIDE_VLAN \
+ UINT32_C(0x3)
+ uint8_t allowed_vlan_pris;
+ /*
+ * This bit field defines VLAN PRIs that are allowed on this
+ * function. If nth bit is set, then VLAN PRI n is allowed on
+ * this function.
+ */
+ uint8_t evb_mode;
+ /*
+ * The HWRM shall allow a PF driver to change EVB mode for the
+ * partition it belongs to. The HWRM shall not allow a VF driver
+ * to change the EVB mode. The HWRM shall take into account the
+ * switching of EVB mode from one to another and reconfigure
+ * hardware resources as appropriately. The switching from VEB
+ * to VEPA mode requires the disabling of the loopback traffic.
+ * Additionally, source knock outs are handled differently in
+ * VEB and VEPA modes.
+ */
+ /* No Edge Virtual Bridging (EVB) */
+ #define HWRM_FUNC_CFG_INPUT_EVB_MODE_NO_EVB UINT32_C(0x0)
+ /* Virtual Ethernet Bridge (VEB) */
+ #define HWRM_FUNC_CFG_INPUT_EVB_MODE_VEB UINT32_C(0x1)
+ /* Virtual Ethernet Port Aggregator (VEPA) */
+ #define HWRM_FUNC_CFG_INPUT_EVB_MODE_VEPA UINT32_C(0x2)
+ uint8_t unused_2;
+ uint16_t num_mcast_filters;
+ /*
+ * The number of multicast filters that should be reserved for
+ * this function on the RX side.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
/* hwrm_func_drv_rgtr */
/*
* Description: This command is used by the function driver to register its
--
2.10.1 (Apple Git-78)
