Hi Wei,

On Wed, 8 Feb 2017 15:51:42 +0000, "Dai, Wei" <wei....@intel.com> wrote:
> > -----Original Message-----
> > From: dev [mailto:dev-boun...@dpdk.org] On Behalf Of Laurent Hardy
> > Sent: Friday, November 18, 2016 1:30 AM
> > To: Zhang, Helin <helin.zh...@intel.com>; Ananyev, Konstantin
> > <konstantin.anan...@intel.com>
> > Cc: dev@dpdk.org
> > Subject: [dpdk-dev] [PATCH] net/ixgbe: ensure link status is updated
> > 
> > In case of link speed set to 1Gb at peer side (with autoneg or with
> > defined speed) and cable not plugged-in when device is configured
> > and started, then link status is not updated properly with new
> > speed as no link setup is triggered.
> > 
> > To avoid this issue, IXGBE_FLAG_NEED_LINK_CONFIG is set to try a
> > link setup each time link_update() is triggered and current link
> > status is down. When cable is plugged-in, link setup will be
> > performed via ixgbe_setup_link().
> > 
> > Signed-off-by: Laurent Hardy <laurent.ha...@6wind.com>
> > ---
> >  drivers/net/ixgbe/ixgbe_ethdev.c |   20 ++++++++++++++++++++
> >  drivers/net/ixgbe/ixgbe_ethdev.h |    1 +
> >  2 files changed, 21 insertions(+)
> > 
> > diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
> > b/drivers/net/ixgbe/ixgbe_ethdev.c
> > index 52ebbe4..513d1d5 100644
> > --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> > +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> > @@ -2095,6 +2095,7 @@ ixgbe_dev_configure(struct rte_eth_dev *dev)
> > 
> >     /* set flag to update link status after init */
> >     intr->flags |= IXGBE_FLAG_NEED_LINK_UPDATE;
> > +   intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
> > 
> >     /*
> >      * Initialize to TRUE. If any of Rx queues doesn't meet
> > the bulk @@ -3117,8 +3118,12 @@ ixgbe_dev_link_update(struct
> > rte_eth_dev *dev, int wait_to_complete)
> >     struct ixgbe_hw *hw =
> > IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> >     struct rte_eth_link link, old;
> >     ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
> > +   struct ixgbe_interrupt *intr =
> > +           IXGBE_DEV_PRIVATE_TO_INTR(dev->data->dev_private);
> >     int link_up;
> >     int diag;
> > +   u32 speed = 0;
> > +   bool autoneg = false;
> > 
> >     link.link_status = ETH_LINK_DOWN;
> >     link.link_speed = 0;
> > @@ -3128,6 +3133,19 @@ ixgbe_dev_link_update(struct rte_eth_dev
> > *dev, int wait_to_complete)
> > 
> >     hw->mac.get_link_status = true;
> > 
> > +   if (intr->flags & IXGBE_FLAG_NEED_LINK_CONFIG) {
> > +           speed = hw->phy.autoneg_advertised;
> > +           if (!speed) {
> > +                   ixgbe_get_link_capabilities(hw, &speed,
> > &autoneg);
> > +                   /* setup the highest link when no autoneg
> > */
> > +                   if (!autoneg) {
> > +                           if (speed &
> > IXGBE_LINK_SPEED_10GB_FULL)
> > +                                   speed =
> > IXGBE_LINK_SPEED_10GB_FULL;
> > +                   }
> > +           }
> > +           ixgbe_setup_link(hw, speed, true);
> > +   }
> > +
> >     /* check if it needs to wait to complete, if lsc interrupt
> > is enabled */ if (wait_to_complete == 0 ||
> > dev->data->dev_conf.intr_conf.lsc != 0) diag = ixgbe_check_link(hw,
> > &link_speed, &link_up, 0); @@ -3145,10 +3163,12 @@
> > ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete)
> > 
> >     if (link_up == 0) {
> >             rte_ixgbe_dev_atomic_write_link_status(dev, &link);
> > +           intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
> >             if (link.link_status == old.link_status)
> >                     return -1;
> >             return 0;
> >     }
> > +   intr->flags &= ~IXGBE_FLAG_NEED_LINK_CONFIG;
> >     link.link_status = ETH_LINK_UP;
> >     link.link_duplex = ETH_LINK_FULL_DUPLEX;
> > 
> > diff --git a/drivers/net/ixgbe/ixgbe_ethdev.h
> > b/drivers/net/ixgbe/ixgbe_ethdev.h
> > index e060c3d..9d335ba 100644
> > --- a/drivers/net/ixgbe/ixgbe_ethdev.h
> > +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
> > @@ -43,6 +43,7 @@
> >  #define IXGBE_FLAG_NEED_LINK_UPDATE (uint32_t)(1 << 0)
> >  #define IXGBE_FLAG_MAILBOX          (uint32_t)(1 << 1)
> >  #define IXGBE_FLAG_PHY_INTERRUPT    (uint32_t)(1 << 2)
> > +#define IXGBE_FLAG_NEED_LINK_CONFIG (uint32_t)(1 << 3)  
> 
> Now there is following macro in DPDK 17.02-rc2.
> #define IXGBE_FLAG_MACSEC           (uint32_t)(1 << 3)
> You can redefine it as #define IXGBE_FLAG_NEED_LINK_CONFIG
> (uint32_t)(1 << 4)

Thanks, I'll send a v2.

Do you agree with the rest of the patch?


Regards,
Olivier

Reply via email to