On 4/16/25 16:59, Ivan Malov wrote:
New X4522 (dual port SFP56) and X4542 (dual port QSFP56) adaptors are
Medford4 (X4) chips that are based on EF10 architecture. An X4 NIC
supports multiple network engine types. This series provides support
only for the Medford2-alike, 'full-feature' (FF) network engine. This
shall not be confused with the concept of 'datapath FW variants': the
FF network engine supports both 'full-feature' and 'ultra-low-latency'
datapath FW variants, with corresponding Medford2-alike feature sets.
The first part of the series provides general support for the adaptors,
whilst the second one adds support for the new management controller
interface for configuration of network port features (netport MCDI).
For now, only support for physical functions (PFs) is concerned. There
is a small number of TODO and FIXME markings in the code. Those are
normal at this development stage and will be removed by future patches
when VF support has fleshed out.
In fact number of TODO and FIXME is frightening. But it is up to you.
Other than that, there are few nits in patches.
Overall looks good.
Andy Moreton (3):
common/sfc_efx/base: update X4 BAR layout and PCI IDs
net/sfc: add Medford4 with only full feature datapath engine
common/sfc_efx/base: add port mode for 8 port hardware
Denis Pryazhennikov (15):
common/sfc_efx/base: add Medford4 PCI IDs to common code
common/sfc_efx/base: add efsys option for Medford4
common/sfc_efx/base: add Medford4 support to NIC module
common/sfc_efx/base: add Medford4 support to EV module
common/sfc_efx/base: add Medford4 support to FILTER module
common/sfc_efx/base: add Medford4 support to INTR module
common/sfc_efx/base: add Medford4 support to MAC module
common/sfc_efx/base: add Medford4 support to PHY module
common/sfc_efx/base: add Medford4 support to TUNNEL module
common/sfc_efx/base: add Medford4 support to MCDI module
common/sfc_efx/base: add Medford4 support to Rx module
common/sfc_efx/base: add Medford4 support to Tx module
drivers: enable support for AMD Solarflare X4 adapter family
common/sfc_efx/base: add new X4 port mode
common/sfc_efx/base: extend list of supported X4 port modes
Ivan Malov (28):
common/sfc_efx/base: update MCDI headers
Hm, bug here. End column is not aligned :)
common/sfc_efx/base: provide a stub for basic netport attach
common/sfc_efx/base: provide defaults on netport attach path
common/sfc_efx/base: obtain assigned netport handle from NIC
common/sfc_efx/base: allow for const in MCDI struct accessor
common/sfc_efx/base: get netport fixed capabilities on probe
common/sfc_efx/base: decode netport link state on probe path
common/sfc_efx/base: fill in loopback modes on netport probe
common/sfc_efx/base: introduce Medford4 stub for PHY methods
common/sfc_efx/base: refactor EF10 link mode decoding helper
common/sfc_efx/base: provide PHY link get method on Medford4
common/sfc_efx/base: implement PHY link control for Medford4
common/sfc_efx/base: introduce Medford4 stub for MAC methods
common/sfc_efx/base: add MAC reconfigure method for Medford4
common/sfc_efx/base: fill in software LUT for MAC statistics
common/sfc_efx/base: fill in MAC statistics mask on Medford4
common/sfc_efx/base: support MAC statistics on Medford4 NICs
common/sfc_efx/base: implement MAC PDU controls for Medford4
common/sfc_efx/base: correct MAC PDU calculation on Medford4
net/sfc: make use of generic EFX MAC PDU calculation helpers
common/sfc_efx/base: ignore legacy link events on new boards
common/sfc_efx/base: add link event processing on new boards
net/sfc: query link status on link change events on new NICs
common/sfc_efx/base: subscribe to netport link change events
net/sfc: offer support for 200G link ability on new adaptors
common/sfc_efx/base: support controls for netport lane count
net/sfc: add support for control of physical port lane count
doc: advertise support for AMD Solarflare X45xx adapters
Same here
