From: Jeremy Spewock <jspew...@iol.unh.edu>
Currently the pf_smoke testing suite only uses the default ports for
sending and receiving packets. When looking at that suite in isolation,
this is fine since its primary goal is to test the physical functions
in the test run (which the defaults should represent). However, since
this suite represents the same coverage that should be tested on VFs, it
makes sense to parameterize the ports that are in use in the suite so
that the same test cases can be used for testing VFs.
Signed-off-by: Jeremy Spewock <jspew...@iol.unh.edu>
---
dts/tests/TestSuite_pf_smoke_tests.py | 22 +++++++++++++++++++---
1 file changed, 19 insertions(+), 3 deletions(-)
diff --git a/dts/tests/TestSuite_pf_smoke_tests.py
b/dts/tests/TestSuite_pf_smoke_tests.py
index 287132e9dd..984a193e8b 100644
--- a/dts/tests/TestSuite_pf_smoke_tests.py
+++ b/dts/tests/TestSuite_pf_smoke_tests.py
@@ -18,6 +18,7 @@
from framework.params.testpmd import SimpleForwardingModes
from framework.remote_session.testpmd_shell import TestPmdShell
from framework.test_suite import TestSuite
+from framework.testbed_model.port import Port
class TestPfSmokeTests(TestSuite):
@@ -35,6 +36,8 @@ class TestPfSmokeTests(TestSuite):
is_blocking: ClassVar[bool] = True
jumbo_frame_len: ClassVar[int] = 9000
num_queues: int = 4
+ sut_egress_port: Port | None = None
+ sut_ingress_port: Port | None = None
def set_up_suite(self) -> None:
"""Increase the MTU of the traffic generator to support jumboframes."""
@@ -48,12 +51,17 @@ def test_jumbo_frame_support(self) -> None:
max_pkt_len=self.jumbo_frame_len,
mbuf_size=[self.jumbo_frame_len + 128],
forward_mode=SimpleForwardingModes.mac,
+ ports=[self.sut_egress_port, self.sut_ingress_port]
+ if self.sut_egress_port is not None and self.sut_ingress_port is
not None
+ else None,
) as testpmd:
testpmd.start()
# Take 26 bytes off the MTU size to account for Ethernet headers
payload_len = self.jumbo_frame_len - 26
packet = Ether() / Raw("X" * payload_len)
- recv = self.send_packet_and_capture(packet)
+ recv = self.send_packet_and_capture(
+ packet, sut_ingress=self.sut_ingress_port,
sut_egress=self.sut_egress_port
+ )
self.verify(
any(hasattr(p, "load") and "X" * 20 in str(p.load) for p in
recv),
f"Jumboframe was not received even when MTU was set to
{self.jumbo_frame_len}.",
@@ -73,6 +81,9 @@ def test_rss_functionality(self) -> None:
forward_mode=SimpleForwardingModes.rxonly,
rx_queues=self.num_queues,
tx_queues=self.num_queues,
+ ports=[self.sut_egress_port, self.sut_ingress_port]
+ if self.sut_egress_port is not None and self.sut_ingress_port is
not None
+ else None,
) as testpmd:
testpmd.set_verbose(1)
src_max = "00:00:00:00:00:01"
@@ -80,7 +91,7 @@ def test_rss_functionality(self) -> None:
Ether(src=src_max) / IP(dst=f"192.168.0.{i+1}") for i in
range(self.num_queues * 4)
]
testpmd.start()
- self.send_packets(send_pkts)
+ self.send_packets(send_pkts, sut_ingress=self.sut_ingress_port)
verbose_stats = TestPmdShell.extract_verbose_output(testpmd.stop())
# Filter down the packets to only the ones with the correct source
MAC
verbose_stats = list(filter(lambda x: x.src_mac == src_max,
verbose_stats))
@@ -105,7 +116,12 @@ def test_rss_functionality(self) -> None:
def test_runtime_modify_num_queues(self) -> None:
"""Ensure that the number of queues on a port can be changed at
runtime."""
with TestPmdShell(
- self.sut_node, rx_queues=self.num_queues, tx_queues=self.num_queues
+ self.sut_node,
+ rx_queues=self.num_queues,
+ tx_queues=self.num_queues,
+ ports=[self.sut_egress_port, self.sut_ingress_port]
+ if self.sut_egress_port is not None and self.sut_ingress_port is
not None
+ else None,
) as testpmd:
try:
testpmd.set_num_queues_all(2, True, verify=True)
--
2.46.0
