On 20/10/2021 08:41, Ferruh Yigit wrote:
On 10/20/2021 7:49 AM, lihuisong (C) wrote:
Hi Ferruh
在 2021/10/20 1:45, Ferruh Yigit 写道:
On 10/11/2021 10:28 AM, Min Hu (Connor) wrote:
From: Huisong Li <lihuis...@huawei.com>
The dev->data->mac_addrs[0] will be changed to a new MAC address when
applications modify the default MAC address by
rte_eth_dev_default_mac_addr_set() API. However, If the new default
MAC address has been added as a non-default MAC address by
rte_eth_dev_mac_addr_add() API, the rte_eth_dev_default_mac_addr_set()
API doesn't remove it from dev->data->mac_addrs[]. As a result, one MAC
address occupies two index capacities in dev->data->mac_addrs[].
Hi Connor,
I see the problem, but can you please clarify what is the impact to the end
user?
If application does as following:
rte_eth_dev_mac_addr_add(MAC1);
rte_eth_dev_mac_addr_add(MAC2);
rte_eth_dev_mac_addr_add(MAC3);
rte_eth_dev_default_mac_addr_set(MAC2);
The 'dev->data->mac_addrs[]' will have: "MAC2,MAC2,MAC3" which has 'MAC2'
duplicated.
Will this cause any problem for the application to receive the packets
with 'MAC2' address?
Or is the only problem one extra space used in 'dev->data->mac_addrs[]'
without any other impact to the application?
I think it's just a waste of space.
True, it is a waste. But if there is no other visible user impact, we can
handle the issue with lower priority and clarifying the impact in commit log
helps to others.
This patch adds the logic of removing MAC addresses for this scenario.
Fixes: 854d8ad4ef68 ("ethdev: add default mac address modifier")
Cc: sta...@dpdk.org
Signed-off-by: Huisong Li <lihuis...@huawei.com>
Signed-off-by: Min Hu (Connor) <humi...@huawei.com>
---
v2:
* fixed commit log.
---
lib/ethdev/rte_ethdev.c | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/lib/ethdev/rte_ethdev.c b/lib/ethdev/rte_ethdev.c
index 028907bc4b..7faff17d9a 100644
--- a/lib/ethdev/rte_ethdev.c
+++ b/lib/ethdev/rte_ethdev.c
@@ -4340,6 +4340,7 @@ int
rte_eth_dev_default_mac_addr_set(uint16_t port_id, struct rte_ether_addr
*addr)
{
struct rte_eth_dev *dev;
+ int index;
int ret;
RTE_ETH_VALID_PORTID_OR_ERR_RET(port_id, -ENODEV);
@@ -4361,6 +4362,20 @@ rte_eth_dev_default_mac_addr_set(uint16_t port_id,
struct rte_ether_addr *addr)
if (ret < 0)
return ret;
+ /*
+ * If the address has been added as a non-default MAC address by
+ * rte_eth_dev_mac_addr_add API, it should be removed from
+ * dev->data->mac_addrs[].
+ */
+ index = eth_dev_get_mac_addr_index(port_id, addr);
+ if (index > 0) {
+ /* remove address in NIC data structure */
+ rte_ether_addr_copy(&null_mac_addr,
+ &dev->data->mac_addrs[index]);
+ /* reset pool bitmap */
+ dev->data->mac_pool_sel[index] = 0;
+ }
+
Here only 'dev->data->mac_addrs[]' array is updated and it assumes
driver removes similar duplication itself, but I am not sure if this is
valid for all drivers.
If driver is not removing the duplicate in the HW configuration, the driver
config and 'dev->data->mac_addrs[]' will diverge, which is not good.
The same MAC address does not occupy two HW entries, which is also a
waste for HW. After all, HW entry resources are also limited.
The PMD should also take this into account.
So, I think, we don't have to think about it here.
I am not sure all PMD take this into account, I briefly checked the ixgbe
code and I am not sure if it handles this.
Also it is possible to think that this responsibility is pushed to the
application, like application should remove a MAC address before setting
it as default MAC...
Yes, the API view is more important than saving one entry in an array.
From API perspective with this patch,
set_default(MAC1)
add(MAC2)
add(MAC3)
add(MAC4)
default=MAC1, Filters=MAC2, MAC3, MAC4
set_default(MAC2)
default=MAC2, Filters= MAC3, MAC4
set_default(MAC3)
default=MAC3, Filters= MAC4
set_default(MAC4)
default=MAC4, Filters=
set_default(MAC5)
default=MAC5, Filters=
Did I get it right? If so, it seems wrong to silently remove the
filters. In which case, it would be easier to just not remove them in
the first place (current behaviour).
If they really need to be removed from the filter list when they are
set_default(), then perhaps they should be restored to it when there is
a new set_default().
What about following logic to be sure HW configuration and
'dev->data->mac_addrs[]' is same:
index = eth_dev_get_mac_addr_index(port_id, addr);
if (index > 0)
rte_eth_dev_mac_addr_remove(port_id, addr);
(*dev->dev_ops->mac_addr_set)(dev, addr);
The logic above seems to be good. But if .mac_addr_set() failed to
execute, the addr has been removed from HW and 'dev->data->mac_addrs[]'.
It's not good.
Agree. So may need to get a copy of 'addr' and add it back on failure.
The concern I have to call 'rte_eth_dev_mac_addr_remove()' after
'dev_ops->mac_addr_set()' is, it may result different behavior on
different PMDs.
For the PMDs that clean the redundant MAC address via 'dev_ops->mac_addr_set()'
may try to remove (although it will fail) the new set default MAC address.
That is why first remove the MAC and later add it back as default
seems safer to me.
Hope for your reply. Thanks.
/* Update default address in NIC data structure */
rte_ether_addr_copy(addr, &dev->data->mac_addrs[0]);
.
