> -----Original Message-----
> From: Min Hu (Connor) <humi...@huawei.com>
> Sent: Wednesday, April 28, 2021 16:37
> To: dev@dpdk.org
> Cc: Yigit, Ferruh <ferruh.yi...@intel.com>; Li, Xiaoyun <xiaoyun...@intel.com>
> Subject: [PATCH v2 1/2] app/testpmd: add link speed check before port start
>
> From: Huisong Li <lihuis...@huawei.com>
>
> Currently, to check whether the configured link_speeds is valid, we have to
> run
> "port start". In addition, if the configuration fails,
> "port->dev_conf.link_speeds"
> maintained in testpmd cannot be restored.
>
> This patch adds the link_speeds check before port start by calling
> dev_configure,
> and resolves these problems.
Not sure about this patch. I don't think you can fix the issue you mentioned.
Probably only hns3 does speed check in dev_configure. I don't see this in other
drivers, not in i40e/ice/mlx.
I guess it's because if it's not supported speed, it will just be UNKNOWN and
user can config again?
BTW, even if this behavior is accepted by others, still some comments below.
>
> Signed-off-by: Huisong Li <lihuis...@huawei.com>
> Signed-off-by: Min Hu (Connor) <humi...@huawei.com>
> ---
> app/test-pmd/cmdline.c | 42 ++++++++++++++++++++++++++++++++++++++++-
> -
> 1 file changed, 40 insertions(+), 2 deletions(-)
>
> diff --git a/app/test-pmd/cmdline.c b/app/test-pmd/cmdline.c index
> 5fdcc1c..ddbc629 100644
> --- a/app/test-pmd/cmdline.c
> +++ b/app/test-pmd/cmdline.c
> @@ -1549,8 +1549,12 @@ cmd_config_speed_all_parsed(void *parsed_result,
> __rte_unused void *data)
> {
> struct cmd_config_speed_all *res = parsed_result;
> + uint32_t old_link_speeds[RTE_MAX_ETHPORTS];
> + struct rte_port *port;
> uint32_t link_speed;
> portid_t pid;
> + portid_t i;
> + int ret;
>
> if (!all_ports_stopped()) {
> printf("Please stop all ports first\n"); @@ -1562,7 +1566,26 @@
> cmd_config_speed_all_parsed(void *parsed_result,
> return;
>
> RTE_ETH_FOREACH_DEV(pid) {
> - ports[pid].dev_conf.link_speeds = link_speed;
> + port = &ports[pid];
> + old_link_speeds[pid] = port->dev_conf.link_speeds;
> + port->dev_conf.link_speeds = link_speed;
> + ret = rte_eth_dev_configure(pid, nb_rxq, nb_txq,
> + &port->dev_conf);
> + if (ret < 0) {
> + printf("Failed to check link speeds for port %d, ret
> = %d.\n",
> + pid, ret);
> + goto roolback;
Why don't you just add restoring all ports speed here and then "break"? No
matter one dev fails or not, all ports will do reconfig from your code logic.
And you type rollback wrongly.
> + }
> + }
> +
> + cmd_reconfig_device_queue(RTE_PORT_ALL, 1, 1);
> +
> + return;
> +
> +roolback:
> + for (i = 0; i <= pid; i++) {
> + port = &ports[i];
> + port->dev_conf.link_speeds = old_link_speeds[i];
> }
>
> cmd_reconfig_device_queue(RTE_PORT_ALL, 1, 1); @@ -1621,7
> +1644,10 @@ cmd_config_speed_specific_parsed(void *parsed_result,
> __rte_unused void *data)
> {
> struct cmd_config_speed_specific *res = parsed_result;
> + uint32_t old_link_speeds;
> + struct rte_port *port;
> uint32_t link_speed;
> + int ret;
>
> if (!all_ports_stopped()) {
> printf("Please stop all ports first\n"); @@ -1635,8 +1661,20 @@
> cmd_config_speed_specific_parsed(void *parsed_result,
> &link_speed) < 0)
> return;
>
> - ports[res->id].dev_conf.link_speeds = link_speed;
> + port = &ports[res->id];
> + old_link_speeds = port->dev_conf.link_speeds;
> + port->dev_conf.link_speeds = link_speed;
> + ret = rte_eth_dev_configure(res->id, nb_rxq, nb_txq,
> + &port->dev_conf);
> + if (ret < 0) {
> + printf("Failed to check link speeds for port %d, ret = %d.\n",
> + res->id, ret);
> + port->dev_conf.link_speeds = old_link_speeds;
> + }
>
> + /*
> + * If the cmd fails to execute, it is necessary to reconfigure device.
> + */
> cmd_reconfig_device_queue(RTE_PORT_ALL, 1, 1); }
>
> --
> 2.7.4
