Hi Xiaoyun,
> -----Original Message-----
> From: dev <dev-boun...@dpdk.org> On Behalf Of Iremonger, Bernard
> Sent: Tuesday, January 19, 2021 9:23 AM
> To: Li, Xiaoyun <xiaoyun...@intel.com>; dev@dpdk.org
> Cc: sta...@dpdk.org
> Subject: Re: [dpdk-dev] [dpdk-stable] [PATCH] doc: fix testpmd sample qinq
> flow rules
>
> Hi Xiaoyun,
>
> > -----Original Message-----
> > From: Li, Xiaoyun <xiaoyun...@intel.com>
> > Sent: Friday, January 15, 2021 3:19 AM
> > To: Iremonger, Bernard <bernard.iremon...@intel.com>; dev@dpdk.org
> > Cc: Iremonger, Bernard <bernard.iremon...@intel.com>;
> sta...@dpdk.org
> > Subject: RE: [dpdk-stable] [PATCH] doc: fix testpmd sample qinq flow
> > rules
> >
> > Hi
> > There are two other mistakes in this section "Sample QinQ flow rules".
> > Can you help to correct those too?
> > 1. testpmd> vlan set qinq_strip on 0
> > Creating QinQ rule(s) command line should be "vlan set extend on 0".
You are correct.
> > Qinq_strip is not relevant to qinq flow rules.
You are correct.
> > 2. The sentence "The above command sets the inner and outer TPID's to
> > 0x8100."
This sentence is correct. Please see lines 4068 to 4076 in i40e_ethdev.c where
both inner and outer TPID's are set to RTE_ETHER_TYPE_VLAN (0x8100).
> > Should be "The following command sets the inner TPID to 0x8100 and
> > sets the outer TPID to 0x88A8".
> >
> > Best Regards
> > Xiaoyun Li
> >
> > > -----Original Message-----
> > > From: stable <stable-boun...@dpdk.org> On Behalf Of Bernard
> > > Iremonger
> > > Sent: Thursday, January 14, 2021 19:20
> > > To: dev@dpdk.org
> > > Cc: Iremonger, Bernard <bernard.iremon...@intel.com>;
> > sta...@dpdk.org
> > > Subject: [dpdk-stable] [PATCH] doc: fix testpmd sample qinq flow
> > > rules
> > >
> > > In the Testpmd Flow rules management section, correct the TPID
> > > values in the Sample QinQ flow rules sub section.
> > >
> > > Fixes: bef3bfe7d5f4 ("doc: revise sample testpmd flow commands")
> > > Cc: sta...@dpdk.org
> > >
> > > Signed-off-by: Bernard Iremonger <bernard.iremon...@intel.com>
> > > ---
> > > doc/guides/testpmd_app_ug/testpmd_funcs.rst | 4 ++--
> > > 1 file changed, 2 insertions(+), 2 deletions(-)
> > >
> > > diff --git a/doc/guides/testpmd_app_ug/testpmd_funcs.rst
> > > b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
> > > index 9be4500..e0020d6 100644
> > > --- a/doc/guides/testpmd_app_ug/testpmd_funcs.rst
> > > +++ b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
> > > @@ -4432,8 +4432,8 @@ The above command sets the inner and outer
> > > TPID's to 0x8100.
> > >
> > > To change the TPID's the following commands should be used::
> > >
> > > - testpmd> vlan set outer tpid 0xa100 0
> > > - testpmd> vlan set inner tpid 0x9100 0
> > > + testpmd> vlan set outer tpid 0x88A8 0
> > > + testpmd> vlan set inner tpid 0x8100 0
> > > testpmd> port start 0
> > >
> > > Validate and create a QinQ rule on port 0 to steer traffic to a VF
> > > queue in a
> > VM.
> > > --
> > > 2.7.4
>
> I will correct the other mistakes too.
>
> Regards,
>
> Bernard.
My replies are inline above.
Regards,
Bernard.
