Based on the specification, eCPRI can only follow ETH (VLAN) layer
or UDP layer. When creating a flow with eCPRI item, this should be
checked and invalid layout of the layers should be rejected.
Fixes: c7eca23657b7 ("net/mlx5: add flow validation of eCPRI header")
Cc: sta...@dpdk.org
Signed-off-by: Bing Zhao <bi...@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viachesl...@nvidia.com>
---
v2: remove the line break for error log message.
---
drivers/net/mlx5/mlx5_flow.c | 22 +++++++++++-----------
1 file changed, 11 insertions(+), 11 deletions(-)
diff --git a/drivers/net/mlx5/mlx5_flow.c b/drivers/net/mlx5/mlx5_flow.c
index a6e60af..859b7f6 100644
--- a/drivers/net/mlx5/mlx5_flow.c
+++ b/drivers/net/mlx5/mlx5_flow.c
@@ -2896,17 +2896,20 @@ struct mlx5_flow_tunnel_info {
MLX5_FLOW_LAYER_OUTER_VLAN);
struct rte_flow_item_ecpri mask_lo;
+ if (!(last_item & outer_l2_vlan) &&
+ last_item != MLX5_FLOW_LAYER_OUTER_L4_UDP)
+ return rte_flow_error_set(error, EINVAL,
+ RTE_FLOW_ERROR_TYPE_ITEM, item,
+ "eCPRI can only follow L2/VLAN layer
or UDP layer");
if ((last_item & outer_l2_vlan) && ether_type &&
ether_type != RTE_ETHER_TYPE_ECPRI)
return rte_flow_error_set(error, EINVAL,
RTE_FLOW_ERROR_TYPE_ITEM, item,
- "eCPRI cannot follow L2/VLAN layer "
- "which ether type is not 0xAEFE.");
+ "eCPRI cannot follow L2/VLAN layer
which ether type is not 0xAEFE");
if (item_flags & MLX5_FLOW_LAYER_TUNNEL)
return rte_flow_error_set(error, EINVAL,
RTE_FLOW_ERROR_TYPE_ITEM, item,
- "eCPRI with tunnel is not supported "
- "right now.");
+ "eCPRI with tunnel is not supported
right now");
if (item_flags & MLX5_FLOW_LAYER_OUTER_L3)
return rte_flow_error_set(error, ENOTSUP,
RTE_FLOW_ERROR_TYPE_ITEM, item,
@@ -2914,13 +2917,12 @@ struct mlx5_flow_tunnel_info {
else if (item_flags & MLX5_FLOW_LAYER_OUTER_L4_TCP)
return rte_flow_error_set(error, EINVAL,
RTE_FLOW_ERROR_TYPE_ITEM, item,
- "eCPRI cannot follow a TCP layer.");
+ "eCPRI cannot coexist with a TCP
layer");
/* In specification, eCPRI could be over UDP layer. */
else if (item_flags & MLX5_FLOW_LAYER_OUTER_L4_UDP)
return rte_flow_error_set(error, EINVAL,
RTE_FLOW_ERROR_TYPE_ITEM, item,
- "eCPRI over UDP layer is not yet "
- "supported right now.");
+ "eCPRI over UDP layer is not yet
supported right now");
/* Mask for type field in common header could be zero. */
if (!mask)
mask = &rte_flow_item_ecpri_mask;
@@ -2929,13 +2931,11 @@ struct mlx5_flow_tunnel_info {
if (mask_lo.hdr.common.type != 0 && mask_lo.hdr.common.type != 0xff)
return rte_flow_error_set(error, EINVAL,
RTE_FLOW_ERROR_TYPE_ITEM_MASK, mask,
- "partial mask is not supported "
- "for protocol");
+ "partial mask is not supported for
protocol");
else if (mask_lo.hdr.common.type == 0 && mask->hdr.dummy[0] != 0)
return rte_flow_error_set(error, EINVAL,
RTE_FLOW_ERROR_TYPE_ITEM_MASK, mask,
- "message header mask must be after "
- "a type mask");
+ "message header mask must be after a
type mask");
return mlx5_flow_item_acceptable(item, (const uint8_t *)mask,
acc_mask ? (const uint8_t *)acc_mask
: (const uint8_t *)&nic_mask,
--
1.8.3.1
