From: Huisong Li <lihuis...@huawei.com>
Currently, max scheduling rates configuration of pg, pri and port are set
to 100000Mbps, which is the maximum bandwidth of hns3 network engine with
revision_id equals 0x21. However, max scheduling rate configuration should
be set to hardware based on the actual hardware board environment.
The max_tm_rate in struct hns3_hw, meaning the rate, is obtained from
firmware. So we should use the variable to configure the max scheduling
rate.
Signed-off-by: Huisong Li <lihuis...@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.hu...@huawei.com>
---
drivers/net/hns3/hns3_dcb.c | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/drivers/net/hns3/hns3_dcb.c b/drivers/net/hns3/hns3_dcb.c
index 857e79e..27ae014 100644
--- a/drivers/net/hns3/hns3_dcb.c
+++ b/drivers/net/hns3/hns3_dcb.c
@@ -62,9 +62,9 @@ hns3_shaper_para_calc(struct hns3_hw *hw, uint32_t ir,
uint8_t shaper_level,
return -EINVAL;
}
- if (ir > HNS3_ETHER_MAX_RATE) {
- hns3_err(hw, "rate(%d) exceeds the rate driver supported "
- "HNS3_ETHER_MAX_RATE(%d)", ir, HNS3_ETHER_MAX_RATE);
+ if (ir > hw->max_tm_rate) {
+ hns3_err(hw, "rate(%d) exceeds the max rate(%d) driver "
+ "supported.", ir, hw->max_tm_rate);
return -EINVAL;
}
@@ -100,7 +100,7 @@ hns3_shaper_para_calc(struct hns3_hw *hw, uint32_t ir,
uint8_t shaper_level,
* ir_calc gets minimum value when tick is the maximum value.
* At the same time, value of ir_u_calc can only be increased up
* to eight after the while loop if the value of ir is equal
- * to HNS3_ETHER_MAX_RATE.
+ * to hw->max_tm_rate.
*/
uint32_t numerator;
do {
@@ -736,7 +736,7 @@ hns3_dcb_info_init(struct hns3_hw *hw)
hw->dcb_info.pg_dwrr[i] = i ? 0 : BW_MAX_PERCENT;
hw->dcb_info.pg_info[i].pg_id = i;
hw->dcb_info.pg_info[i].pg_sch_mode = HNS3_SCH_MODE_DWRR;
- hw->dcb_info.pg_info[i].bw_limit = HNS3_ETHER_MAX_RATE;
+ hw->dcb_info.pg_info[i].bw_limit = hw->max_tm_rate;
if (i != 0)
continue;
@@ -1405,7 +1405,7 @@ hns3_dcb_info_cfg(struct hns3_adapter *hns)
hw->dcb_info.pg_dwrr[0] = BW_MAX_PERCENT;
hw->dcb_info.pg_info[0].pg_id = 0;
hw->dcb_info.pg_info[0].pg_sch_mode = HNS3_SCH_MODE_DWRR;
- hw->dcb_info.pg_info[0].bw_limit = HNS3_ETHER_MAX_RATE;
+ hw->dcb_info.pg_info[0].bw_limit = hw->max_tm_rate;
hw->dcb_info.pg_info[0].tc_bit_map = hw->hw_tc_map;
/* Each tc has same bw for valid tc by default */
--
2.9.5
